20 Most Recent 2006 Isuzu Ascender Questions & Answers


6 radios, 2 with amps, the other 4 do not have amps.external
there are 2 cars
aswsered in full yesterday, gone today.
short wheel base and long
the long base amp left rear. side.
the short base RR.
is that clear?

2006 Isuzu... | Answered on Mar 05, 2017


Recall for this, it's just your low beam relay under the hood.

2006 Isuzu... | Answered on Feb 04, 2017


You have a leaking heater core.

2006 Isuzu... | Answered on Dec 29, 2016


the hazard switch is bad.
or do like we do, exercise it like 5 to 10 times
and bingo it now works (if luck of the Irish)
they can stick and if got kids that play, 10x this.

2006 Isuzu... | Answered on Dec 01, 2016


Replace the whole thing, make sure to tell the autoparts store which one you have, manual climate control or automatic. If I were you, I'd also replace the pigtail, those seem to melt often.

2006 Isuzu... | Answered on Dec 01, 2016


lost the manual.
buy one and not get stranded for simple things or where is fuse X
its in the glove box.
new

http://www.helminc.com/helm/Result.asp?Style=helm&Mfg=AIM&Make=AIM&Model=ASCE&Year=2006&Category=2&Keyword=&Module=&selected%5Fmedia=


used cheaper on feabay.

2006 Isuzu... | Answered on Nov 08, 2016


Hopefully not low on oil...(a must recheck oil level) with this indication...also look for an oil leak under your Isuzu. Could just mean that the "change oil soon" indicator has not been re-set...If you had the oil changed professionally, they should re-inspect this for you ASAP...Sounds like you take car of your car...don't let this go without a full inspection for oil level, and any leaks...Hope this helps.

2006 Isuzu... | Answered on Apr 25, 2016


x2 , fuses, fuses are first. always with electrics. right? sure.
2nd step is scan the PCM, oops you didnt.

2006 Isuzu Ascender

here ill RTM , for you,,, online at mitchells.
usa cars, only. so......

ok ready?
there are 5 head lamp fuses
and 2 HL relays.
fact.
3 fuse just for Low beams
seen here.
if both fuse below are 0v, both end,s
that means Relay 46 is bad or not energized by the BCM
and if the coil is hot, (left side 46) then the relay is bad
if the coil is not hot, the BCM is malf'ing(lots of ways,ask)
we scan it. if the BCM is not closing relay 46.
easy huH?
get B0951? dtc?
B2575?
do you have DRL lighting (canada does, i cant guess)
we dont.

fuse and 46
26131262-4ck0s2e11zusaohrt4godt42-3-0.jpg
this is the input to BCM, if Headlamp glows below. ?
then the PCM say you turn them on, if not , bad deal, ask.
26131262-4ck0s2e11zusaohrt4godt42-3-1.jpg
and last is pin 5 hot? hot means 12vd
if not the bcm is bad, if above works. easy no?
26131262-4ck0s2e11zusaohrt4godt42-3-3.jpg

2006 Isuzu... | Answered on Mar 23, 2016


check the sending unit for the oil light at the engine block

Mike

2006 Isuzu... | Answered on Mar 20, 2016


The light is activated by an an oil pressure switch. With the engine not running there is no pressure so it lights up. When the oil recirculates, the pressure increase and the light goes out. Locate yours and change it, they are fairly inexpensive. If it stays lit after a change it may indicate something more serious.

2006 Isuzu... | Answered on Mar 16, 2016


The oil light is not an indication of oil level; rather it is an indication of oil pressure. If the oil pressure is low enough to light the oil light, you should be hearing some rattling in the engine. Otherwise, it is possible that the oil pressure sending unit is defective. You are lucky if that is the case, because some vehicles are wired that if the oil pressure sensor indicates low pressure, the engine will shut down to protect itself. You should have the oil pressure checked with a mechanical gauge ASAP and take whatever corrective measures are necessary.

2006 Isuzu... | Answered on Feb 15, 2016


why not read on alldata.com, its all there,
remove a screw?


25402002-5afre3fjdbg1gkzo1rpx5eib-3-0.jpg
  1. Block the wheels to prevent the vehicle from moving.
  2. Remove the rubber ash tray inserts and rubber mat from the console.
  3. Remove the floor shift control knob. Refer to Floor Shift Control Knob Replacement.
  4. Remove the center console shift lever bezel, Buick only. Refer to Console Shift Lever Bezel Replacement (Refer To List 1).
  5. Remove the console storage compartment. Refer to Front Floor Console Compartment Replacement.
  6. Remove the center console retaining screws.
  7. Adjust the parking brake to the full-up, or fully engaged position.
  8. Release the 2 forward trim extensions ears attached to the lower instrument panel (I/P), Buick only.
  9. Slide the console rearward and raise the rear of the console in order to expose the electrical connectors.
  10. Disconnect the electrical connectors, as necessary.
  11. Adjust the parking brake to approximately the halfway position.
  12. Remove the center console from the vehicle.
  13. If replacing the floor console base, remove the following and retain for transfer:
    • 13.1.
      Remove the HVAC control module (if equipped).
    • 13.2.
      Remove the armrest.
    • 13.3.
      Remove the HVAC module and duct assembly.
    • 13.4.
      Remove the cupholder.
    • 13.5.
      Remove the HVAC upper duct.
or read the FSM (buy one) factory service manual, its all there every step and photos too, (all cars. are like that)
or
http://www.scantool.net/software/alldata-diy-1-month-subscription.html

log in, and see that. and more.

2006 Isuzu... | Answered on Feb 06, 2015


it unbolts from clamps and of cable connections ,like all cables do.
the install it.
if this is your first cable, ever. use, youtube and see 100s doing them on all cars.

2006 Isuzu... | Answered on Feb 06, 2015


Dismantling and mantling.
  1. Remove the I/P accessory trim plate. Refer to Instrument Panel Accessory Trim Plate Replacement (Refer To List 1) or Instrument Panel Cluster Trim Plate Bezel Replacement (Refer To List 2).
  2. Remove the HVAC control module screws.
  3. Depress the HVAC control module tabs (3) and remove the HVAC control module (2) from the I/P (4).
  4. Disconnect the electrical connectors (1) from the HVAC control module (2).

fix the module..... what ever.
and put it back
then see the last step.

Refer to Control Module References for programming and setup information.
then states
If the HVAC control module is replaced, an automatic re-calibration of all the actuators will occur. No additional procedures are necessary.

2006 Isuzu... | Answered on Aug 10, 2014

Not finding what you are looking for?
2006 Isuzu Ascender Logo

137 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers

Mike

Level 3 Expert

4369 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ascender Isuzu

  • Ascender Isuzu

Most Popular Question

s factory amp located in 2006 isuzu

  • Cars & Trucks
Loading...