20 Most Recent 1999 Lexus RX 300 Questions & Answers

John, needs to be scanned to determine fault.

1999 Lexus RX... • Answered on Oct 19, 2020

No, nothing will drop down into the pan when it is removed. The only precaution that you will need to prepare for is the transmission fluid. Supporting the pan and directing the fluid can be messy. Wear safety glasses, lay down cardboard, have plenty of rags on hand and a large drain pan.

1999 Lexus RX... • Answered on Sep 18, 2018

Is it a standard? If so sounds like the clutch is giving up and needs replacing. If it is an automatic then check fluid level might be low, that can cause slippage.

1999 Lexus RX... • Answered on Dec 25, 2017

i am suggesting you a link which will help you to solve the problem easily i had tried this link before http://toolsnyou.com/

1999 Lexus RX... • Answered on Dec 12, 2017

Visit the on-line store, known as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem. 1999 lexus rx300

1999 Lexus RX... • Answered on Oct 14, 2017

what are the new codes clearing / resetting doesnt fix the problem the p0171 code has about ten different causes just changing or cleaning the sensor may not have been your problem P0171 System Too Lean Bank 1 rescan and get all codes then look up each one most sites have causes and solutions for obd ll trouble codes

1999 Lexus RX... • Answered on Jul 23, 2017

Check the pressure in the fuel pump Check the fuel filter for dirt When there is weak fuel pressure, it generates this type of failure Also check the compression on the engine cylinders

1999 Lexus RX... • Answered on May 15, 2017

Inspect the CV joint boots for damage. It's possible they are torn and have let road dirt into the grease causing premature wear. Have the automatic idle control valve cleaned or replaced.

1999 Lexus RX... • Answered on Mar 29, 2017

run the fault codes to determine if there are any sensors operating out of set parameters your indications are that the HO2S sensors are not operating correctly or cannot set the ECM for the air/fuel ratio could be a problem MAP/Baro sensor, faulty injectors (spraying and not atomizing), low fuel pressure or simply at 17 years old or a guestimate Klm of around 340,000 klms the motor is a bit tired anyway run the fault codes first and then having a wet and dry compression test ( a qualified service mechanic will know what I mean) done will determine the engine condition

1999 Lexus RX... • Answered on Feb 01, 2017

You have a problem in your Evaporative Emission Control System. Not much you can do without the right equipment. A mechanic needs to diagnose this with his testing tools. Good luck!

1999 Lexus RX... • Answered on Dec 22, 2016

I don't live in a state that has emission laws, but that code is emission related. It should be a simple fix, since it is an older car I would go in order of highest probability that either the line is broken, the solenoid needs to be replaced, or a break/corrosion in the wiring. There could be a couple of other things but unlikely.

1999 Lexus RX... • Answered on Nov 14, 2016

Yes, looks normal, and good. Calculated load is not much meaning, as it changes constantly. ECT of, oh that is centigrade, not sure how that translates to Fahrenheit, but it may be low from not running long... Your fuel trims (both short term and long term-STFT, LTFT) are very good-showing that fuel is not being added or subtracted by the computer to maintain correct air/fuel ratio. Fuel trim numbers should be close to zero. It is when fuel trim changes by double digits-either positive or negative-that there is an indicated problem. For example, say you had a vacuum hose leak- sucking in extra air to the engine- then you could see STFT number go positive by double digits-meaning the computer senses a lean condition and is adding fuel to compensate. But your fuel trims show the air/fuel ratio must be correct-no change in fuel trims-the positive 2.3 in LTFT is negligible- not a problem.

1999 Lexus RX... • Answered on Nov 08, 2016

code p 0330 refers to knock sensor (KS)2 bank 2 ---circuit malfunction===causes wiring--KS---ECM it is possible that in changing the harness there is a problem connection or the connection to ks2 is not correct ( not on properly)

1999 Lexus RX... • Answered on Oct 01, 2016

John, the computer will have to be scanned to find fault.

1999 Lexus RX... • Answered on Feb 21, 2016

Not finding what you are looking for?
1999 Lexus RX 300 Logo

719 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2001 Lexus RX 300
2001 Lexus RX 300

361 Questions

2000 Lexus RX 300
2000 Lexus RX 300

330 Questions

2002 Lexus RX 300
2002 Lexus RX 300

149 Questions

2003 Lexus RX 300
2003 Lexus RX 300

108 Questions

Top Lexus Experts


Level 3 Expert

4376 Answers

Brad Brown

Level 3 Expert

18666 Answers

Greg Bernett
Greg Bernett

Level 3 Expert

2993 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

RX 300 Lexus

  • RX 300 Lexus

Most Popular Question

getting extremely poor gas mileage 99

  • Cars & Trucks