2001 Lexus RX 300 - Answered Questions & Fixed issues

google 2001 lexus rx300 yaw rate sensor location took less than 5 seconds. https://www.justanswer.com/lexus/4zhj3-lexus-yawrate-sensor-lexus-rx300.html

check fuse 50 in the engine bay. I think it wrongly attributed to the 'rear defogger' which is already mentioned in the internal fuse box as fuse 43. https://fuse-box.info/lexus/lexus-rx300-xu10-1999-2003-fuses also check the contacts on the windshield for continuity. ..

A lot of times the fuel filter location for a newer model car like you have is it's going to be in the fuel pump

You don't have to worry much, but it has to be fixed. What was the code #?

Basically, stop driving it until you can get the transmission serviced. If you can safely jack up the vehicle and support it so it cannot fall on you, you can possible save some money by checking all the electrical connections to the transmission. Sometimes the problem is a loose or bad connection. If that does not work, your safest bet is to bring it to a certified mechanic, especially one who specializes in Lexus.

Most likely a bad wheel speed sensor or wiring harness issue.

Due to the age of your vehicle, the brushes in the fan motor are worn out. you will have to replace the fan motor, it is not serviceable.

I don't believe that this model has a orifice tube. Sorry, it might be internal in another part

You need to drop the sub frame and support motor from above using a brace or bracket from side to side.

If it works OK then yes it could be the bulb

Watch this video for removal of control and relay replacement

2001 Lexus RX 300 - Openbay

https://www.openbay.com/intake-manifold.../2001-lexus-rx-300/chicago... 2001 lexus rx 300 4dr suv base fq oem 1 500 ... rely on very precise measurements of air to properly mix in fuel, so these leaks lead to poor engine performance.

Lexus RX300 Valve cover gasket replacement - YouTube

? 11:21 www.youtube.com/watch?v=brV5MEgzfHs Feb 17, 2014 - Uploaded by Stevie Kicks Lexus RX300 engine repair. ... Nice video Stevie. I was watching it to see if I could spot the bank 1 sensor 1 air/fuel sensor. I have to replace ...

a latch and or handle rod disconnected /broke a retaining clip need to remove the door panel to access the latch

No it's built in seatbelt

if the car won`t turn over then it could be a starter problem if the battery is as you say fully charged. check voltages at the starter. it could be a bad connection or starter relay.

FIX/CHECK IGNITION COIL FIRST, BEFORE YOU DO ANYTHING ELSE

How long have you been driving or owned a car? Your A/C is set on front "defrost" instead of main. Turn off the defroster for the front and select the switch to read "main" or if your A/C panel uses icons to display, press the one where it looks like the airflow is blowing air (represented by arrows) towards you and not the windshield. The arrows on your buttons or electronic display refer to which way the air is flowing. Choose the one you want where the arrows show the airflow is blowing out towards you and/or turn off your defroster. (If you have a knob to select airflow, turn it so it is no longer on "defrost" and it points to the main airflow blowing outward).

there will be a air flow setting knob that controls whether air is defrost or on feet or from the console vents.

I wonder if these two codes are related. P0330 could be due to a bad Knock Sensor which might affect the timing thereby causing issues with air/fuel ratio i.e. P1130

you have to disconnect the window regulator motor connector and apply 12v at connector. using a jumper wire connect to the motor side connector one to the negative cable and the other to positive connector.