20 Most Recent
2002 Volvo V40 Wagon - Page 9 Questions & Answers
How to change 2007 Volvo S40 2.4L lower Intake manifold gasket and valve cover gasket
the service manual covers all that ,every step.
battery lug NEG - pulled first. (isolated)
step 2 ,
depressurize fuel line, not get gas in eyes.
tell the kids to not smoke or uncle Fester too.
i PULL THE FUEL PUMP FUSE OR RELAY AS ENGINE RUNS AND HEAR IT SLOWLY DIE IN SAY 1MIN OR SO,..NOW CAR IS SAFE TO WORK ON.
NOW LEARN THERE ARE TOOLS TO OPEn a line
and I have no idea what Volvo uses, but the manual will call it out. (OR GOOGLE IT TO LEARN FOR VOLVO)
some fuel lines conns have built in latches, to trip
Read IT.
seen here.
https://eautorepair.net/Marketing/Default.asp
Cooling fan removal on 2010 volvo XC60
1. Disconnect the negative battery cable.
2. Raise the vehicle and remove the plastic body panel located at the front of the engine bay and behind the front bumper.
3. Remove the upper radiator support bolts.
4. Unplug the electrical connector from the cooling fan.
5. Remove the mounting bolts for the fan.
6. Remove the fan.
7. Installation is the reverse of removal.
How do i replace the return hose #26 to the coolant overflow tank on 2004 Volvo xc90
1. Disconnect the negative (black) battery cable from the vehicle's battery. Locate the coolant tank and hose #26.
2. Remove the hose from the coolant tank by loosening the clamp and gently pulling off the hose.
3. Cut the new replacement hose to the desired length.
4. Attach the new hose to the coolant tank, ensuring that the clamp is tightened properly.
5. Reconnect the negative battery cable and check for any coolant leaks.
2010 volvo s40 trunk lid mirco switch replacement
The microswitch for the Volvo S40 trunk lid is located inside the trunk lid panel. On the left side of the trunk lid panel, you should be able to locate the access panel for the microswitch. Remove the panel to access the switch. Disconnect the electrical connector from the switch and remove the mounting screws to remove the microswitch. Install the replacement switch by tightening the mounting screws and reattaching the electrical connector. Test the switch to make sure it works correctly and then reinstall the access panel.
Location of my tcm on my Volvo xc90 awd 2.9
The Transmission Control Module (TCM) on a Volvo XC90 AWD 2.9 is located under the driver's side dash, attached to the underside of the steering column. It is mounted behind the steering wheel and can be accessed by removing the lower dashboard panel.
2010 xc60 volvo Does the throttle body have to be reset after cleaning
Yes, it is recommended to perform a throttle body adaptation or reset procedure after cleaning the throttle body on a 2010 Volvo XC60. This is because cleaning the throttle body can remove built-up carbon deposits and change the air flow through the throttle body, which can affect the engine's idle speed and performance.
To perform the adaptation or reset procedure, follow these steps:
- Reinstall the cleaned throttle body and reconnect all electrical connectors and hoses.
- Turn the ignition key to the "On" position, but do not start the engine.
- Wait for 30 seconds to allow the throttle body to initialize.
- Turn off the ignition key and wait for 10 seconds.
- Start the engine and let it idle for 10 minutes with all electrical accessories turned off.
- Turn off the engine and wait for 10 seconds.
- Restart the engine and take it for a test drive to ensure proper idle speed and performance.
If the engine still does not idle well after performing the throttle body reset procedure, there may be other issues causing the problem, such as a vacuum leak or a faulty sensor.
Not finding what you are looking for?