2001 Hyundai XG300 - Answered Questions & Fixed issues


If the starter cranks the engine at normal cranking speed, it's not a starter problem. So you have to check for fuel and spark.

2001 Hyundai... | Answered on Mar 16, 2018 | 150 views


A noise like you are describing is not related to the rack and pinion steering. It is related to a cv joint. If you can find a parking lot that has no cars in it. turn in a tight circle to the right and listen then do the same to the left. You will hear the noise and can tell which one it is coming from.

2001 Hyundai... | Answered on Oct 21, 2017 | 156 views


Those lights rarely burn out. More likely the switch on the brake handle came unplugged. Try grounding the wire from the ebarke switch with the key on.


0996b43f8024e4ce-lxsvs4ftyjtcqsaualeaxmu4-5-0.gif
For the mirrors, I would pull up the control panel and probe for power. Trace the power through the mirror sekection switch, etc.


0996b43f8024ee04-lxsvs4ftyjtcqsaualeaxmu4-5-2.gif

2001 Hyundai... | Answered on Aug 30, 2017 | 65 views


First never attempt to clean or touch the element of a Mass Airflow sensor, it will damage it. A dirty air filter can put MAF sensor out of range. Change the air filter. The popping during acceleration is an indication of fuel starvation. Change the fuel filter. Do the OBDII scan again and delete the stored fault history so that anything else that comes up will be current. Use the current fault history as a guide to any further repairs to avoid buying parts you don't need

2001 Hyundai... | Answered on Jun 07, 2017 | 143 views


you need to connect a diagnostic machine to your obd socket, you can actuate the tps through the machine, it will also give you the correct location of wires/connectors.

2001 Hyundai... | Answered on Apr 25, 2017 | 132 views


The 350 code is a circuit problem with the coils and the variable valve gears being stripped can be a definite driveability issue .

2001 Hyundai... | Answered on Apr 11, 2017 | 123 views


crank sensor is located on the front of the engine behind the
timing belt covers and is mounted to the front of the engine block. the alternator has to be moved to feed the harness down the front side of the block to replace the crank sensor it has a tone wheel that may have to be moved the remove and replace sensor

2001 Hyundai... | Answered on Mar 26, 2017 | 105 views


Here's a link on cleaning your,TPS. How to Clean Throttle Position Sensor

2001 Hyundai... | Answered on Sep 15, 2016 | 175 views


Here's a link showing you your cylinder locations. Specifications Firing Order AutoZone com

2001 Hyundai... | Answered on Sep 15, 2016 | 64 views


You can possibly buy the belt for your model car that has no a/c. Just ask the clerk at the parts store for a belt for the vehicle that does not have a/c. If they do not sell one then you will have to take off the compressor and replace it with a pulley and braket.That is if they sell one for that particular vehicle.

2001 Hyundai... | Answered on Sep 09, 2016 | 166 views


to answer that would need need the 3 ltr V6 motor repair manual and from the fuel section
the pressure number
without a pressure gauge
if the fuel pump is pumping fuel to the injector rail
test if fuel pressure regulator is not full of fuel and the vacuume pot is holding


26221373-iuia05yowlw3utsriegmwzzl-4-0.jpg

26221373-iuia05yowlw3utsriegmwzzl-4-2.jpg

2001 Hyundai... | Answered on Jun 19, 2016 | 58 views


All ECM's are flashed to the vehicle's VIN#. The answer is no

2001 Hyundai... | Answered on Apr 28, 2016 | 55 views


Like you said the first two codes are tps related. Check your wire harness and wiring could be shorted to ground or have a broken wire. The third code is for map sensor no response shorted or open circuit.

2001 Hyundai... | Answered on Apr 24, 2016 | 102 views


have the fault codes read to find the sensor that has failed
if it happening when you have the foot on the brake, it could be a problem brake booster

2001 Hyundai... | Answered on Apr 10, 2016 | 92 views


Should be a hole facing upwards above the light. A Phillips screwdriver goes into the hole to turn the teeth.

2001 Hyundai... | Answered on Feb 22, 2016 | 103 views


When any gear is slipping in an automatic transmission , that is a sign that the transmission is worn out, and needs to be rebuilt or replaced.

2001 Hyundai... | Answered on Dec 07, 2015 | 60 views


The drivers side kick panel

2001 Hyundai... | Answered on Dec 07, 2015 | 289 views


Start with the basics, are there any DTC's ? How old are the spark plugs, air and fuel filters, are there any vacuum leaks?

2001 Hyundai... | Answered on Dec 07, 2015 | 129 views


If you are talking about a missfire, you should have a check engine light and trouble codes stored in the engine computer.

2001 Hyundai... | Answered on Nov 03, 2015 | 216 views

Not finding what you are looking for?
2001 Hyundai XG300 Logo

704 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...