20 Most Recent 2006 Cadillac SRX Questions & Answers

If the sunroof hasn't completed closing or cannot be reset by the BCU the vehicle will assume it is open and will not allow the door locks to activate.

It is normal for the top radiator hose to be hotter than the lower hose. The top hose brings the heated coolant from the engine to the radiator, and the lower hose returns the cooler water from the radiator back to the engine to help keep the engine at proper temperature. For the smell, check to see if you have any oil leaks, especially where the oil may run/drip on to the exhaust manifold. Check the valve cover gaskets, and look for excessively oily areas on the bottom of the car to see if you can find where the oil is leaking from.

Sorry Bill but you don't the tool's or knowledge to take on this job . Control module's involved. Which one does your vehicle have ? Power Sunroof System Components -- CF5 The power sunroof system consists of the following components: • Front glass control module and motor assembly • Front sunshade control module and motor assembly • Sunroof switch • Front glass panel • Front sunshade • Power supply for the front glass control module and motor assembly logic: RAP relay • Power supply for the power sunroof system: SUNROOF MOD fuse 40 A Power Sunroof System Components -- C3B The power sunroof system consists of the following components: • Front glass control module and motor assembly • Front sunshade control module and motor assembly • Sunroof switch • Front glass panel • Front sunshade • Rear sunshade control module and motor assembly • Rear sunshade switch • Rear sunshade • Rear fixed glass panel • Power supply for the front glass control module and motor assembly logic: RAP relay • Power supply for the power sunroof system: SUNROOF MOD fuse 40 A

could be the water pump ,grab hold of the pump pully and pull it back and forth see if it is loose on there , why would change a motor becasue of a chanin anyhow

How do I take radio off mute off 2006 cadillac srx

First, try a different key. Second, remove all other electronics from the vehicle including phone charger and all other car keys. If it still won't work, get the trouble code read. That's the next step. Yeah, I know you can't drive it anywhere to get it read. So your only other choices are: buy a scan tool or call a tow truck and have it towed to a shop. Without knowing the code it could be several things and some can be really expensive so you don't want to start throwing parts at it.

There is an electric motor that controls the blend door. You probably have an issue at the blend door. Either the motor is bad, or the actuator isn't connected. The actuator arms are know to crack and allow the motor to move without moving the actuator.

This is a CLASSIC symptom of an evaporative emissions issue. GM has had tons of issues with this system. Don't even think about fuel pump at this point. Read this post on how EVAP works. http://ricksfreeautorepairadvice.com/evaporative-emissions-system-primer/ Then read this post on service bulletins GM has issued on the EVAP system http://ricksfreeautorepairadvice.com/p0440-p0441-p0442-p0446-evap-codes-on-gm-vehicleshicles-p0440-p0441-p0442-p0446/

Hooking between the neg. post an neg. cable an pulling fuse's is not a good way to do a parasitic draw test on your vehicle . Pulling fuse's wakes up module's an you will see a draw . You need to do it non-intrusively . Your vehicle has a bunch of control modules an pulling fuse's will wake them up. Try this way . The BEST Way TO Perform Parasitic Draw Test Diagnose Battery Drain Parasitic Draw Chevy Trailblazer Chevrolet Truck Battery Dies Overnight Part

Try the Cadillac users forum - someone else may have had that problem. The only other thing I can suggest is get a dealer to look at it.

Check your manual if that doesn't work radio is falty

anti theft? bad starter?

You are lucky that you have the replacement as a guide to show you how the original console is held in place. If you are handy, you can get a tool from an auto parts store that will help you loosen the retaining clips in the positions shown on the replacement item. You may need a helper to hold onto the in-place console while you carefully pry on the clips to get them loose. A small, clean rag put into place between the pry tool, your hands and the headliner will help keep things tidy. Good luck

check for cylinder compression's,take it from there