Top 20
2003 Honda CR-V Questions & Answers
Where is the horn located on a 2003 CRV Honda
https://www.youtube.com/watch?v=sgzldlc_3kc
. You can find the original manufacturer's horns for the Honda CR-V by raising the hood and looking at the front. There should be one horn on each side of the license plate behind the bumper.
Hi,
I would like to know if the front seat belt
I don't know if this is something you want to get into? You decide.
Front Seat Belt Replacement
SRS components are located in this area. Review the SRS component locations and the precautions and procedures before performing repairs or service.
NOTE: Check the front seat belts for damage, and replace them if necessary.
Front Seat Belt
- Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
- Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
- Slide the front seat forward fully.
- Pull the lower anchor cover (A) back, and remove the lower anchor bolt (B).
- Remove the B-pillar lower trim panel.
- Remove the upper anchor cover (A), and remove the upper anchor bolt (B).
- Disconnect the seat belt tensioner connector (A), and detach the harness clip (B) from the retractor (C). Remove the upper retractor mounting bolt (D), and the lower retractor bolt (E), then remove the front seat belt (F) and retractor.
- If necessary, remove the front seat belt protector (G).
- Remove the B-pillar upper trim.
- Remove the shoulder anchor adjuster (A).
- Install the seat belt in the reverse order of removal, and note these items:
- Assemble the washers, collar, and bushing on the upper and lower anchor bolts as shown.
- Check that the retractor locking mechanism functions.
- Apply liquid thread lock to the anchor bolts before reinstallation.
- If the seat belt tensioner has been activated, replace the front seat belt protector with a new one.
- Before installing the anchor bolts, make sure there are no twists or kinks in the seat belt.
- Make sure the seat belt tensioner connector is plugged in properly.
- Reconnect the negative cable to the battery.
- Enter the anti-theft code for the radio, and then enter the customer's radio station presets.
- Reset the clock.
- Do the PCM idle learn procedure and the power window control unit reset procedure.
Upper anchor bolt installation
Lower anchor bolt installation
Seat Belt Buckle
- Make sure you have the anti-theft code for the radio, and then write down the frequencies for the preset buttons.
- Disconnect the negative cable from the battery, and wait at least 3 minutes before beginning work.
- Remove the front seat.
- If equipped, remove the center table.
- Remove the under seat storage box.
- Remove the center cover, driver's, passenger's.
- Driver's: If equipped with seat heater, remove the harness band (A), and disconnect the seat subharness connector (B). If equipped without seat heater, detach the seat belt switch connector clip (C). Detach the seat belt buckle tensioner clip (D), and harness clip (E).
The check engine icon keeps coming on. When I
Yes, buy a new cap. If the light comes on again, just have the computer scanned and then post the trouble codes here. If you are in the US, you can get a free scan at your local parts store.
Hello
I got a honda
It's stalling at lights because of no brake lights. Meaning the brake light switch and transmission power to shut off the overdrive is not working. Any time you touch the brake, overdrive is turned off because power to trans is stopped when brake lights come on. Both these operations are performed by the same switch under the dash and mounted so that when the brake pedal is depressed, the switch button comes out and turns on the brake lights in turn shutting down the overdrive. Adjust or replace that brake light switch and you're good to go.
I have a terrible vibration
Swap the front tires to the back and see if this is a possible tired related problem like a tire cord separating
I have been getting an
If you have a scan tool that shows sensors, you can clear codes and run your vehicle while checking the operation of your O2 sensors. Then check the specifications and compare. If bad, best is to replace bad sensor. If you go online, you may find more affordable parts.
www.rockauto.com
wwwpartsgeek.com
Checking engine light
When you get a check engine light it means a fault has occurred and a fault code for that is in memory, now you need the fault codes or codes read to see what is going on and then troubleshoot the system.
Not finding what you are looking for?