1994 Jeep Grand Cherokee - Answered Questions & Fixed issues

There are plastic rivets taht need to be pull and possibly to be cut. and there should have 2-3 bolts per side which need to be removed. The rivets or clips can be purchase at the dealer or local Automotive store, such as autozone and etc.

1994 Jeep Grand... | Answered on Nov 03, 2019 | 123 views

These conditions MUST be ruled out entirely.
Check for any of the following conditions/mechanical problems.
AIR INDUCTION SYSTEM - must be free from leaks
ENGINE VACUUM - must be at least 13 inches in neutral
ENGINE VALVE TIMING - must be within specifications
ENGINE COMPRESSION - must be within specifications
ENGINE EXHAUST SYSTEM - must be free of any restrictions or leaks
ENGINE PCV SYSTEM - must flow freely
TORQUE CONVERTER STALL SPEED - must be within specifications
POWER BRAKE BOOSTER - no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR - plugged or restricted injector; control wire not connected to correct injector.

Unfortunatly, a scan tool will be required to monitor o2 sensor voltages while the engine is running in closed loop. This code you are displaying is NOT an easy solution to trace down. I expect you had an exhaust leak and is why the cats were replaced? Anyway, if so, the PCM can reset the light after a few GOOD trip readings occur that will satisfy the PCM's no fault signal, otherwise the JEEP dealer is going to be your only solution and a pressure test should be performed.

1994 Jeep Grand... | Answered on Oct 13, 2019 | 2,324 views

You have a blown power booster. It is leaking vacuum and you will have a hard brake pedal and find it tough to stop your vehicle. Replace the power booster and you will have brakes and no more leaking air sound.

1994 Jeep Grand... | Answered on Jul 04, 2019 | 34 views

Try this one, says its for a 1994 Cherokee, no mention of engine type but it look like a V8 would..
1994 jeep grand cher.-gbvdwzazhmsxyfemnsd4fk1i-3-4.png

994 jeep no ac routing-gbvdwzazhmsxyfemnsd4fk1i-3-2_0.png

1994 Jeep Grand... | Answered on May 01, 2019 | 339 views

Check the motor and transmission mounts

1994 Jeep Grand... | Answered on Mar 09, 2019 | 80 views

On a 94 Jeep Grand Cherokee check fuse 17 should be a seven and a half amp fuse if the fuse is good go under the hood to your power distribution center look for the air conditioning relay swap it with one of the other ones several of those are Universal fit see if it works then

1994 Jeep Grand... | Answered on Feb 05, 2019 | 657 views

I'm having a problem with my tranny not wanting to shift automatically at all. Seems like a dead stop its stuck in low gear. Have to manually shift and does not go into overdrive. I have a 1993 Jeep Grand Cherokee. Can anyone help me cause I've swiched out throttle control sensor, filter change, new tranny cooler and heavy duty lines. I'm at a loss and scratching my head. Any advice would be greatly appreciated

1994 Jeep Grand... | Answered on Dec 31, 2018 | 1,591 views

first place I'd look is around the perimeter of the heads (I assume you mean head gaskets?) Make sure you haven't inadvertently gotten a wire pinched in between the head & block somewhere.

1994 Jeep Grand... | Answered on Sep 30, 2018 | 195 views

Hi. Thanks for your question. For issue related to jeep cherokee laredo you can visit https://www.reliable-store.com and download the entire workshop manual which includes all the information along with the diagrams for better understanding. Good day!

1994 Jeep Grand... | Answered on Mar 23, 2018 | 133 views

so all 3 FOBs are dead? is that it??????
so the which part of the system is failing
the ASD relay cuts starts, 7 ways, one is security. called VTSS.

i guess the security light is telling you, that it is not happy? in the dash cluster, is that it?
94 or 96?
so it , flashes ext. lamps, honks horn, and wont start.
page 8q-1 FSM.


endless post. on topic. read it, try it.

better yet, diagnose it.
scan the PCM to find out why the ASD relay drops out
does it? that is the first test in all, no starter.

if the battery is discharged, bad things happen as the security logic
goes nuts. (the chips dont yet run on "free energy" )

1994 Jeep Grand... | Answered on Feb 24, 2018 | 211 views

Change your compressor with the new one.

1994 Jeep Grand... | Answered on Feb 23, 2018 | 78 views

that is a boot retainer clip and should be attended to as ir prevents dirt getting into the joint
There is a wire around that point that goes to a sensor got the ABS and it may be loose or damaged
have the boot checked out and if it is cracked have a drive line shop replace it

1994 Jeep Grand... | Answered on Feb 14, 2018 | 54 views

Check your exhaust many times it'll be a o2 sensor wire touching the manifold causing the short to ground. Start there let us know. Hope this helps.

1994 Jeep Grand... | Answered on Jan 10, 2018 | 260 views

Have you checked it for engine codes? Trouble codes should point you in the right direction.

1994 Jeep Grand... | Answered on Dec 26, 2017 | 77 views

possible tps issue.

1994 Jeep Grand... | Answered on Dec 24, 2017 | 61 views

Change the temperature sending unit/temp sensor. When starting, the sensor will tell the computer to put the engine in cold start mode to give a bit more fuel and raise the idle a little so it WILL start and keep running without ever touching the throttle. Once warm-up is completed, this sensor will tell the computer to stop the cold start mode and go to normal run mode. THAT is your only problem.

1994 Jeep Grand... | Answered on Dec 07, 2017 | 120 views

Not finding what you are looking for?
1994 Jeep Grand Cherokee Logo

2,882 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides