20 Most Recent 2006 Plymouth Breeze Questions & Answers


You replaced the BCM with a junk yard one , it probably needs to be reconfigured an programmed . Dealer only . In my thrity years as a automotive technician i have seen this , people changing parts without know what they were doing . Take it to a qualified repair shop .
Information for the speedo an odometer come over the CCD bus from the BCM ! I bet you have no idea what the CCD bus is ? You have no clue as to how this vehicle works .
Chrysler CCD Chrysler Collision Detection Data Bus carprog

2006 Plymouth... | Answered on Mar 13, 2017


Working in the wheel arches there will be screws to remove inner wing liner , easier to take wheels off, you will then have access to the bumper fittings, then in the boot\trunk remove for carpet and trim along edge to access the retaining bolts / screws, fitting is just a reverse

Plymouth Breeze... | Answered on Feb 05, 2019


Often this has to do with sensors on the engine. Get it checked out at a proper garage.

Plymouth Breeze... | Answered on Jan 02, 2017


If the gearshift is stiff to move possibly need a gearshift cable.

Plymouth Breeze... | Answered on Feb 24, 2016


possibly need to replace the ignition switch

Plymouth Breeze... | Answered on Feb 24, 2016


If your battery meter/readout is constant ?
That means your system voltage is the same all the time. That is probably a good sign.
I would expect to see the battery gauge be lower before starting the vehicle and then be the same all the time, after the engine is running (which means the charging system is maintaining the system voltage)
If it doesn't show lower before the engine starts you may have to check the gauge operation to verify its working.
You should be able to go to your local parts store and they will probably check your charging system and battery for Free (it is good for sales)
Let me know if this helps you at all.

Plymouth Breeze... | Answered on Mar 12, 2015


I need some clarification. Did you replace the belt because it broke? If so you may need to replace the head. The problem is if the belt breaks when your moving it usually damages the head and thus needs to be replaced.

Plymouth Breeze... | Answered on Jan 21, 2015


Hello, you should be able to find a helicoil kit at Auto Zone or most parts stores. good luck

Plymouth Breeze... | Answered on Jan 08, 2015


Check your ground wires, make sure they got good connection, also make sure the exhaust is not melting the power cable to the starter, also check the steel sleeve that shields the power cable from the exhaust manifold. Good luck.

Plymouth Breeze... | Answered on Dec 04, 2014


When changing the timing belt you need to place the cam shaft a TDC( clock wise), then rotate the crankshaft to TDC (clockwise), then back off the crankshaft (counter clockwise) THREE TEETH then back (clockwise) 1/2 tooth before TDC place your timing belt arround the crankshaft- water pump- and camshaft finally putting arround the tensioner pulley, holding 25 flbs of torque on the tensioner pulley to get the correct tension then push up on the hydrolic tensioner and tighten and you should have it.... rotate the crankshaft twice, if the camshaft pulley ends back on TDC then you have it correct.

Plymouth Breeze... | Answered on Nov 17, 2014


fa gid aboud it ... better to have mech,do it

Plymouth Breeze... | Answered on Oct 20, 2014


You can purchase a polishing kit that will clear up the lens some what. See http://www.amazon.com/3M-Headlight-Lens-Restoration-System/dp/B001AIZ5HY

They also can be purchased at your local automotive parts store.

Plymouth Breeze... | Answered on Sep 27, 2014


Did you check the motor mounts?

Plymouth Breeze... | Answered on Aug 02, 2014


What parts have been replaced?

Plymouth Breeze... | Answered on Aug 02, 2014


That belt would be for power steering,accessed from below would be easier, the pump bracket is the adjustment for it and the serpentine belt would need to be off to remove and install the other one.

Plymouth Breeze... | Answered on May 13, 2014


Usually means check the battery for low charging...could be dirty connection posts...also can mean alternator is not 100% These are free checks at your local auto store...Hope this helps.

Plymouth Breeze... | Answered on Apr 02, 2014


There is NO Bleeding of a fuel injected vehicle

Once the fuel pump is running & the injectors working,
all air is blown into the cylinders

Plymouth Breeze... | Answered on Mar 15, 2014

Not finding what you are looking for?
Cars & Trucks Logo

1 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Plymouth Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Plymouth Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Breeze Plymouth

  • Breeze Plymouth

Most Popular Question

bad pcm speedometer death odometer

  • Cars & Trucks
Loading...