20 Most Recent 2003 Chrysler Voyager Questions & Answers

check the antifreeze and it may be time for a new thermostat but if all else fails the radiator needs flushing

2003 Chrysler... | Answered on Oct 30, 2017

Check wire to transmission it sounds like a ground out when you hit a bump ,

2003 Chrysler... | Answered on Oct 04, 2017

sounds like ya starter is locked up or frozen you can contact chrysler and see if they got a part for it or a local auto shop might be best to go to autozone they can diagnose the starter to see if its working or not

2003 Chrysler... | Answered on Apr 21, 2017

dont try removing the steering wheel as the airbag will cause this to be a problem , adjust the tracking until the wheel is in the position you want , make sure you adjust the track rods equally on each side , this is a little bit of trial and error if your doing it your self ,

2003 Chrysler... | Answered on Nov 11, 2016

check for water in the harness connections at the transmission

2003 Chrysler... | Answered on Jul 24, 2016

If goes to a right,left side tie rod in 1/2 turn.or goes to a left ,right side tie rod in 1/2 turn.

2003 Chrysler... | Answered on Jun 25, 2016

It may need factory programming.

2003 Chrysler... | Answered on Jul 23, 2015

body module is for anti theft mostly,use your key fob to unlock your doors then put your key in and unlock then start

2003 Chrysler... | Answered on Jul 23, 2015

Put a voltmeter across the terminals (main current supply) and check for power. If power get someone to try start and watch the voltage, it shouldn't change, if it drops dramatically you have a cable/joint/fuse/battery problem. If no power, then look for cable/fusable link problems.

If it doesn't change and has power, check the solenoid terminal to earth, it should have no power until a start is attempted. If it doesn't have power when a start is attempted check the connectors back to the ignition key (you'll need a wiring diagram.)

If you do get power when trying to start remove the starter motor and check it... The solenoid should:

1/ Kick the drive gear forward
2/ close a set of 'power' contacts to drive the starter.

If you get a 'click' when installed (1) is usually happening, but it may be there is dirt on the shaft which stops it getting to (2) and therefore it won't kick the engine over... a well placed hammer blow can sometimes prove that, but it's better to just take it off the engine and test it on the bench.

2003 Chrysler... | Answered on Jul 08, 2015

under nearside dash where glovebox is there is a little panel take off panel filter is there just pull down

2003 Chrysler... | Answered on Jun 29, 2015

If u mean bypass as in putting a new wire in, I'd be in plugging the Ecu connector and lambda sensor then running a simple test to make sure u got the right wire , a four wire lambda is 2 heater wires usually the same colour which when on is positive 1 5v Ecu feed and a earth

2003 Chrysler... | Answered on Jun 27, 2015

in the fuse box under hood

2003 Chrysler... | Answered on Mar 19, 2015

Should be on top of the intake near the upper radiator hose.

2003 Chrysler... | Answered on Mar 08, 2015

I have attaced a picture.
I hope this helps.

2003 Chrysler... | Answered on Mar 08, 2015

Leave it off if your in a hotter clime ,refit only in lattitudes where you get cold and snow ,now leave it alone and have a cup of tea and a ciggy then go back to it and you will see it straight away

2003 Chrysler... | Answered on Feb 22, 2015

Not finding what you are looking for?
2003 Chrysler Voyager Logo

255 questions posted

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Voyager Chrysler

  • Voyager Chrysler

Most Popular Question

put new starter wont start

  • Cars & Trucks