20 Most Recent 1997 Isuzu Hombre Questions & Answers


If the light is on, a code is stored. Get the code read. Then post it. Guessing which code is stored is a waste of time.

1997 Isuzu... | Answered on Dec 04, 2017


the 4cy. or the v6 (4,x,V)
there are plugs, wrong plugs, or
gaped wrong, and new plugs can be bad, I have a nice collection of new mutant spark plugs. on the wall.
wires bad. whey you replace spark plugs
the wires break so put new NGK wire on it , mag wire are best.
or you mixed the wire order.
do not mix the HV wire( the large high voltage wire)
that apples to both distriubors and the 4 cylinder 2.2L with 2 coil packs
the V6 has one coil pack
the gap is .045 v6 and spark gap 2.2 is .040"

1997 Isuzu... | Answered on Dec 07, 2016


2.2l gm S10 is the real name of truck
4.3L is real name of V6, GM

your other posts tell me , what you did wrong
that leak is not a leak its called flooding
when you damage the spark wires,
spark ends,
and every cylinder with dead spark floods
can even drip fuel from the exhaust port flanges.
seen it vast times.
next time I will read all post
or better you stick to one, post one prob
and add to it. is best
good day.

1997 Isuzu... | Answered on Dec 07, 2016


this is really GM S10 truck
it's not an Isuzu, only the silly badge is isuzu.
2.2L GM engine
4.4l V6 Gm engine
why not tell what is wrong first then we can play easter egg hunts all day.
if the scan tool told you EVAP fails
then
1: buy new gas cap or tighten yours.
2: then using scan tool reset the error.
3: drive
4: if the scan errors for EVAP are gone, good.
5: if not, then the tank vents leak, a leak down test is warranted now, (i bet you lack tools?)

1997 Isuzu... | Answered on Nov 27, 2016


it could be a fuse but that fuse is usually your doom light to.the wire may have become loose,or the lighter itself is shot.

1997 Isuzu... | Answered on Jan 27, 2016


it is a sender unit not a sensor unit
take the wire off it and see if the gauge falls to zero
put the wire back on and if it goes to hot ,replace the sender unit
the difference is that temp gauge sender units have 1 wire to it and work through the gauge to it then through a heat altered resistor in it to earth (ground)
A temp sensor has more wires to it and works from the ecm
it closes a circuit when the coolant reaches a preset temperature, sending a signal to the ECM which then closes a relay to make the fan/s run to cool the radiator

1997 Isuzu... | Answered on Oct 10, 2015


MT trans. got it. (said clutch let up.. is the clue)
engine is running right? (sorry)
and you shift to all gears, and car does not move, RIGHT?

if the clutch slips and car will not move in ALL gears.
the clutch is bad, or if a cable clutch, never setting free play on cable is the cause,... done 100s.
or if hydraulic actuated clutch pedal (im too lazy to look)
then if it fails the car can only moved if you start engine in gear.
see?
please post all steps.
i get in car,
i start engine in neutral. (did you) or start in gear with clutch to floor.?
i then select all gears, and release clutch and car will not move.
like that.... and win. (i can diagnose any clutch, ive wrecked many racing, so.... see all horrors) and fixed them by self. all.

if you can only move car , starting engine in gear.?
that is bad clutch cable or actuator (slave or master cylinder)

is the clutch locked all times, or slips all the time.
see? only that need be said.
and 10 other symptoms. (chatters, noises, grabs, etc)

1997 Isuzu... | Answered on Apr 22, 2015


most likely a 3rd bolt that comes from the opposite direction and screws into the stater housing It may also even have a nut on it as well

1997 Isuzu... | Answered on Dec 05, 2014


See me at website for images can only send one through this channel. www.autorepairhelp.us

Best Regards,

Master Tech Lee

HEATER BOX SHIELD
Image
Heater Box Heat Shield
Remove or Disconnect
1. Fasteners that retain heat shield to heater box assembly.
Image [ Heater Box Heat Shield
Install or Connect
1.Fasteners that retain heat shield to heater box assembly.
Tighten
-Bolts Screws to 2.2 N.m (25 lb in).
HEATER ASSEMBLY
Image ' Heater Hoses
Image ' A/C Evaporator Tube Assembly
Image ' Evaporator Core
Image ' Evaporator Core Assembly
Image ' Heater Assembly
Remove or Disconnect
1.Engine coolant. Refer to Draining and Filling Cooling System in Engine Cooling.
2.Heater hoses. Refer to Heater Hoses.
3.Instrument panel. Refer to Instrument Panel Replacement in Interior Trim.
4.Air inlet assembly. Refer to Air Inlet Assembly Replacement.
5.Vacuum lines.
Important
-Clearly label vacuum line connections.
6.Heater assembly studs inside engine bay.
7.Blower motor resistor. Refer to Blower Motor Resistor.
8.Stud inside heater core housing.
-Stud is revealed by removing the blower motor resistor.
9.Rear case screws.
10.Heater assembly.
11.Seals.
Imagt
Imagt
Imagt
Imagt
Imagt
Heater Hoses
A/C Evaporator Tube Assembly
Evaporator Core
Evaporator Core Assembly
Heater Assembly
Install or Connect
1.Seals.
2.Heater assembly.
3.Rear case screws.
4.Stud inside heater core housing.
Tighten
-Stud to 1.9 N.m (17 lb in).
5.Blower motor resistor. Refer to Blower Motor Resistor.
6.Heater assembly studs inside engine bay.
Tighten
-Studs to 1.9 N.m (17 lb in).
7.Vacuum lines.
8.Air inlet assembly. Refer to Air Inlet Assembly Replacement.
9.Instrument panel. Refer to Instrument Panel Replacement in Interior Trim.
10.Heater hoses. Refer to Heater Hoses.
11.Engine coolant. Refer to Draining and Filling Cooling System in Engine Cooling.
-Check the system for leaks.


Auto Repair Help US 699e5693-1e5b-4101-9428-b5c0b4e46f83.jpg

1997 Isuzu... | Answered on Sep 06, 2014


Most radios let you set them like this - select bandwidth FM/AM then tune to a favourite station, find the row of numbered buttons under digital display (usually 1 - 5) then press and hold button 1 for a few seconds, the station will be set to button 1, so to speak. Repeat tuning to another station then press button 2, etc...some radios have up to 15 slots per band. How many stations do you listen to....

To recall station 1, press button 1 ..button 2.......... Red.

1997 Isuzu... | Answered on Apr 05, 2014


It may be as simple as your knob on the switch being wore out and it not actually turning the switch .or the switch may be bad and will need replacing.

1997 Isuzu... | Answered on Oct 28, 2013


Check for a vacuum leak in your hoses it may be as simple as this or a fuel filter I say just change it to make u sleep better at night lol

1997 Isuzu... | Answered on Oct 28, 2013


97 nissan transmissionno 5th gear. does it have a O.D. electronic switch that con go out

1997 Isuzu... | Answered on Oct 28, 2013


sounds like your starter is stuck or sticking to your transmission not allowing you to get out of park,,this is what your problem is

1997 Isuzu... | Answered on Oct 23, 2013

Not finding what you are looking for?
1997 Isuzu Hombre Logo

109 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14848 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Hombre Isuzu

  • Hombre Isuzu

Most Popular Question

check temp sensor

  • Cars & Trucks
Loading...