20 Most Recent 2002 Mercury Grand Marquis Questions & Answers


So, when removing the sender, do you have to remove the entire intake manifold?

2002 Mercury... | Answered on Oct 23, 2019


I am not familiar with this model but often this sort of fault is caused by one of the various inhibitors on the system that stops it's use in a dangerous conditions. Pressing the brake pedal for instance automatically stops the cruise otherwise it would try to speed up when you are trying to slow down. If this is a manual transmition vehicle it will have microswitches on the clutch, gear change, brake and hand brake. Automatics will have them on the brake, gear change and hand brake. Check these microswitches for correct operation.

2002 Mercury... | Answered on Jul 12, 2019


This sounds most like a worn lock actuator which wouldn't be uncommon. If you need a diagram on how to replace, let me know.

2002 Mercury... | Answered on Sep 09, 2018


struts ball joints etc are wore out , we can not fix them online go see a mechanic locally

2002 Mercury... | Answered on Feb 26, 2018


Take your vehicle to a qualified repair shop . We could tell you think's to check , but doubtfull you could .

2002 Mercury... | Answered on Dec 15, 2017


Need to locate the source of drain. After waiting half hour after shutdown, connect ammeter to car and measure current drain. Then one by one remove a fuse until you see the current go down - note it. Do it with all and check out the circuit with the largest drop. You should be drawing around 50 milliamps ordinarily for your radio clock, radio memory, etc.

2002 Mercury... | Answered on Sep 16, 2017


Could be your fluid is low.

2002 Mercury... | Answered on Aug 28, 2017


i would tell you to do fuel pump test's pressure an flow ,voltage drop testing etc..... Do you know what these are ? Testing is the way to finding the problem ! Videos on youtube showing how to do it.
Testing Electric Fuel Pump Problems with Voltage Drop Test
you can find free wiring diagrams here
http://www.bbbind.com/free_tsb.html Do you know what a wiring diagram is , how to read one ?
Electric Testing Techniques You Need to Know

2002 Mercury... | Answered on Jun 22, 2017


Best way is to remove oil pan and weld in a new nut for drain plug, next best is to retap the threads to a slightly larger size and replace drain plug.( get plug then retap to fit the new plug.) may change from std thread to metric to be able to do this. Lastly the least effective way i know of- buy a small rubber expansion plug that fits in and tighten bolt that runs through it to expand the plug. ( this should work for a while till you can get it fixed properly.

2002 Mercury... | Answered on Feb 28, 2017


There can be a water fitting to the heater hose located under the rear of the intake manifold.

2002 Mercury... | Answered on Jan 28, 2017


Check the DPFE sensor and the 2 hoses going to it. Has to be on a scanner to see the voltage the DPFE is sending.

2002 Mercury... | Answered on Dec 20, 2016


If you want to fix this yourself your going to need to develop some kind of electrical diagnostic skill's . Finding wiring diagrams at www.bbbind.com . watch videos on youtube for basic electrical testing . You'll need to buy a DVOM - digital volt ohm meter . Electrical Series Tools Theory Of Auto Electrical Diagnosis and Repair Electrical Troubleshooting Basics EricTheCarGuy It mite be best for some people to just take it to a qualified repair shop .

2002 Mercury... | Answered on Oct 02, 2016


Fuel pump relay, 4.6L System overview
Relay center box 1, wheelwell, front, LH side

2002 Mercury... | Answered on Aug 12, 2016


I do not think this is a safe idea, the tank is plastic and if you drive through it you may cause a fire.

2002 Mercury... | Answered on Jun 11, 2016


Good news! Your car does not have a history of such problems. Now, what could be the answer?
I would start with the battery connections and cables.
Disconnect the cables and clean the battery posts shiny bright with sandpaper or a pocket knife, or whatever.
Then clean inside the battery terminals to also shiny bright.
Then look carefully at the thick wires that are attached to the terminals, right where they end.
Be sure there is no corrosion there.
It can be cleaned with boiling water, if you see any.
Have someone check the starter and also the starter solenoid, either of these could be in the process of failing.
God bless your efforts.

2002 Mercury... | Answered on May 24, 2016


You need a new switch (rheostat).

2002 Mercury... | Answered on Mar 21, 2016


If you have standard halogen bulbs:

  1. Burned out light bulb; or
  2. Fried wires between the dashboard wiring harness and the headlight bulb connectors; or
  3. Fried headlight bulb connectors.
If you have HEI emitters:
  • Failed ballast.

2002 Mercury... | Answered on Dec 21, 2015

Not finding what you are looking for?
2002 Mercury Grand Marquis Logo

448 questions posted

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4388 Answers

Marvin
Marvin

Level 3 Expert

85231 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Grand Marquis Mercury

  • Grand Marquis Mercury

Most Popular Question

blower stays high swich will not change

  • Cars & Trucks
Loading...