20 Most Recent 1993 Jeep Wrangler Questions & Answers

Put your road wheels in the straight ahead position. Disconnect the negative terminal on the battery. It'll disable the air bag if one is fitted. Unscrew the centre boss through the holes on the back of the steering wheel.
**NOTE** Air bags are sensitive and explosive so BE CAREFUL!!
Gently disconnect the wires to the back of the centre boss and put it somewhere where it won't get dropped or kicked by accident. Disconnect the wires to the steering wheel controls. Loosen the bolt in the centre of the wheel. DON'T remove it all the way! Leave it in 2 or 3 turns.
You can either use a two armed puller to free it or hit it from behind with a rubber hammer.
Leaving the bolt in will stop it hitting you in the face when it comes loose.

1993 Jeep... | Answered on Mar 07, 2018

Just a guess: wiring harness.

1993 Jeep... | Answered on Jan 18, 2018

nothing wrong with the ECM unless it has the voltage regulator as part of the system
indicates faulty wiring and faulty alternator
have a load test done on the battery
have an auto electrician do a full charging system check
charging voltage should be 14.5-14.8 volts DC
battery voltage should be 12-13.5 volts dropping to 11 volts when cranking the engine
make sure that the drive belt tension is correct and the belt is in good condition

1993 Jeep... | Answered on Dec 22, 2017

check you manual, fuse box cover and clean the contacts on the fuse box and where it plugs in

1993 Jeep... | Answered on Dec 02, 2017

front, and rear. only. (cept the gaping hole with oil filter off ,the filter acts as a plug too)
cam gears off.
and flywheel off.

posted over 300 time.
the book , free, ,real
click YJ
click ENIgne.


1993 Jeep... | Answered on Jan 14, 2017

the fsm covers this. (fact.serv. man)
ill paste the words, the book is free. to read.
booster out steps are there in chapter BRAKES
chapter 5
page 22
(1) Loosen but do not remove nuts attaching master
cylinder to booster (Fig. 3).
(2) Remove instrument panel lower trim cover.
(3) Remove retaining clip attaching booster push
rod to brake pedal (Fig. 4).
(4) Remove bolts/nuts attaching booster to dash
(5) In engine compartment, loosen vacuum hose
clamp and disconnect vacuum hose from booster
check valve (Fig. 5).
(6) Remove master cylinder attaching nuts and remove
cylinder from mounting studs on booster
(7) Carefully move master cylinder aside and remove

the clip is here.
the book is free, to read, and posted over 100 times now...


1993 Jeep... | Answered on Mar 27, 2016

that ax-15 , behind cummin's.
3.9L , 50 lbs more torque, there, may be ok.
when buying custom mod. cars this is all normal.
1: nobody can fix your car, due to its not stock.
2: get stranded on the road, far from home and nobody will wont to touch it..
3: finding out just what the hacker did to make it work, now that takes alive human to do that... for sure.
hacker=modder=custom jeep.

you may need to go to jeep.com
and look at every front pinon shaft ever used
on the ax-15
my guess just 1.

it's too short because you have 3.9L cummins to Ax-15 adapter
there, and the mod guy, just ignored this.??? no photos presented by you.
my guess, (wild)
is it's this?


we are blind here can;t see all those custom parts
not hardly
if you look there
it has recessed plate to make the distance match.
and mounts match.
and has a custom collar for the throwout to slide on.
all custom parts.
and many suppliers. unknown yours.

1993 Jeep... | Answered on Mar 26, 2016

Sounds like a spark plug or distributor problem.... Change out all your spark plugs and check your wires for breaks. Check fuel injectors for build-up.

1993 Jeep... | Answered on Feb 07, 2016

whoever rebuit it has got the shifter interlock wrong or syncro rings/springs in wrong

1993 Jeep... | Answered on Apr 03, 2015

usually ATF oil,fill to plug level

1993 Jeep... | Answered on Apr 03, 2015

you will need a scan toool to see if the ECU is recieving a signal fron speed sensor,if it is mechanical the cable or drive has failed

1993 Jeep... | Answered on Apr 03, 2015

if it's a concentric slave cylender ther should be a second hose coming out of bellhousing with a bleeder on it,if not look for slave cyl on side or top of bellhousing

1993 Jeep... | Answered on Apr 03, 2015

unscrew the plastic fasia around dash abd remove,then unscrew speedo

1993 Jeep... | Answered on Apr 03, 2015

lots of screws to get this one out

1993 Jeep... | Answered on Apr 03, 2015

In the fuse box under the hood near the battery.

1993 Jeep... | Answered on Mar 03, 2015

Not finding what you are looking for?
1993 Jeep Wrangler Logo

391 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Wrangler Jeep

  • Wrangler Jeep

Most Popular Question

93 jeep wrangler sat several months now

  • Cars & Trucks