Top 20 2000 Chrysler Town & Country - Page 6 Questions & Answers

Assuming the check engine light is not on, I would check the fuel pressure with a gauge before and after startup.
Could be a fuel pump relay or the pump, among other things.

2000 Chrysler... | 109 views | 0 helpful votes

Frozen from Rust?

Usually have to replace about 2/3 of the cables
& whatever else need to be done

2000 Chrysler... | 21 views | 0 helpful votes

If the engine cranks but does not start at first try, I would check the fuel pressure.
If the engine cranks slowly or not evenly, I would check voltage at the battery and the starter.

2000 Chrysler... | 96 views | 0 helpful votes

cal an electrician to check whether you have power leak or faulty battery.

2000 Chrysler... | 85 views | 0 helpful votes

Take it to a garage,

2000 Chrysler... | 16 views | 0 helpful votes

If this an intermitent problem, couldn't be a fuse problem, I bet that this is a wires harnesses problem, some wire in bad condition or a window switch go to bad (can included the window motor in the inspection).

2000 Chrysler... | 580 views | 1 helpful votes

have your alternator check sounds like its not charging your battery

2000 Chrysler... | 52 views | 0 helpful votes

If security light is on and the vehicle will not start, then you need to find out the trouble code that set and turned on the security system.You can try locking and unlocking the doors with the key to see if the system will reset.

2000 Chrysler... | 684 views | 0 helpful votes


2000 Chrysler... | 613 views | 0 helpful votes

A small plug, normally on the bottom of the radiator tank, used for draining coolant and water. It's also known as a drain petcock.Sometimes close to the bottom on side of radiator facing the engine.

2000 Chrysler... | 435 views | 1 helpful votes

see the image attached . 1( look for the first one box under the dash 2( in front how you see in the picture. God bless you


2000 Chrysler... | 220 views | 0 helpful votes

Could be a fuel pump relay or throttle position sensor.
Is the check engine light on ?

2000 Chrysler... | 56 views | 0 helpful votes

You did not say whether the inside or outside, so here is the instructions to both.

3_21_2012_1_44_00_am.jpgAnd here is for the outside door handle

2000 Chrysler... | 415 views | 0 helpful votes

Inside the transmission attached to the valve body.

2000 Chrysler... | 60 views | 0 helpful votes

Hi Bernard:
The FLASHER is located under the driver dash it is a round fuse (it's located adjecent to the fuse block, and it's square, yellow in color).

Also, I suggtes to check for power at the junction box under the dash at terminals 1 and 6 with the combination flasher removed. Then check with a powered test lamp if test lamp lights pin 7 when signaling left and pin 8 when signaling to the right.

If the test results are correct, replace the Combination Flasher/DRL (Daytime Running Lights) module.


Gain access to the multifunction switch connector. Locate the Light Blue/Yellow wire and ground it. This should activate the right side turn signals. Locate the Light Blue/White wire and ground it. This should activate the left side turn signals. If both sides do work, the problem is in the multifunction switch. Verify the Black wire in the same connector is grounded at all times. If so, replace the multifunction switch.



Here is some reading on how the system works.

The Combination Flasher/DRL is a module providing turn signal, hazard warning, and daytime running light functions (for Canadian vehicles), and has been designed with internal relays to take advantage of low current switching requirements in the vehicle. It is plugged into the junction block at positions three and four, where all wiring associated with its operation is terminated. The junction block is adjacent to and left of the steering column of the vehicle.

On vehicles built for use in the United States, only position four is used. Vehicles built for use in Canada utilize both positions three and four.

To gain access to the device, remove the lower steering column cover and knee blocker.

The combination-flasher/DRL may be operated in its hazard warning mode either with or without the ignition circuit being active. However, in order to operate in the turn signal mode or the DRL mode, the ignition circuit must be completed to the module.

While the combination-flasher portion is idle, there is no current drawn through the module. The device does not become active in the turn signal or hazard warning modes until a signal ground circuit is supplied to either of the turn signal inputs or the hazard warning input. With the ignition OFF, there is no current drawn through the module.

While the ignition is ON, the front turn signal filaments are illuminated steadily thus providing the DRL function. The DRL function may be inhibited by applying a signal ground input from either the park brake circuit or the headlamp relay activation circuit.

Hope this helps; also keep in mind that your feedback is important and I will appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

2000 Chrysler... | 3,454 views | 0 helpful votes

Most likely it is a bad switch/relay on the door. You should be able to actuate the switch with your finger when the door is open. If nothing happens when you push the switch in and out then its possible that you may need to replace the switch. You might first try removing the switch and checking it to see if it is stuck and make sure the wiring is connected securely. Your local Chrysler Dealership should have the replacement part and could replace it for you if you feel like its something you don't want to tackle.

2000 Chrysler... | 467 views | 2 helpful votes

the culprit is fuse f12 -a 10 amp fuse on the right end of the small fuse panel by below the hood release under the dash. I had same problem - something is blowing the fuse; in my case it was something in the backup light circuit. This fuse is the power source for the relay coils that power all the other circuits that stopped working.

2000 Chrysler... | 391 views | 0 helpful votes

You need to tell us what your question is.

2000 Chrysler... | 62 views | 1 helpful votes

could be tha water pump or belts

2000 Chrysler... | 252 views | 0 helpful votes

Not finding what you are looking for?
2000 Chrysler Town & Country Logo

764 questions posted

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Town & Country Chrysler

  • Town & Country Chrysler

Most Popular Question

van will not fire turn key off several

  • Cars & Trucks