20 Most Recent 2000 Chrysler 300M Questions & Answers

0helpful
2answers

I just hook up an

DOES THE RADIO PLAY? HERE ARE THE FACTORY WIRING COLORS FOR THE RADIO HARNESS, RECHECK YOUR WORK. IF U FIND NOTHING THEN IF THE RADIO PLAYS THE CD PLAYER IS DEFECTIVE, IT HAPPENS BELIEVE ME.

2001 Chrysler 300M Car Stereo Wiring Diagram
Car Radio Battery Constant 12v+ Wire: Pink
Car Radio Accessory Switched 12v+ Wire: Red/White
Car Radio Ground Wire: Chassis or Strap
Car Radio Illumination Wire: N/A
Car Stereo Dimmer Wire: Orange
Car Stereo Antenna Trigger Wire: Orange/Red
Car Stereo Cell Phone Mute Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: Located under the rear deck in the trunk.
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Dark Green
Left Front Speaker Negative Wire (-): Brown/Red
Right Front Speaker Positive Wire (+): Violet
Right Front Speaker Negative Wire (-): Dark Blue/Red
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Brown/Yellow
Left Rear Speaker Negative Wire (-): Brown/Light Blue
Right Rear Speaker Positive Wire (+): Dark Blue/White
Right Rear Speaker Negative Wire (-): Dark Blue/Orange
6/28/2021 2:31:24 PM • 2000 Chrysler... • Answered on Jun 28, 2021
0helpful
1answer

Take headlight cover off to change headlight?

yes if you are replacing the whole headlight unit otherwise you can replace the globe by removing the rear cover.
3/6/2019 11:40:46 PM • 2000 Chrysler... • Answered on Mar 06, 2019
0helpful
1answer

Why is my 2000 chrysler 300m not turning over but my fuse box and relay box clicking and my dash lights flashing? Battery is at 100% and replaced starter relay

Ensure you battery is within the warranty period. Sounds like a weak vehicle battery, even though it's at a full charge. Have alternator charging system checked. Take the time to trace and clean all relays. Ensure all ground wires are secure and serviceable and not broke or frayed. Double check the battery ground wire. Be sure battery connections are clean and tight. Have vehicle professionally checked on a machine. It is often worth the price.
3/6/2019 11:23:01 AM • 2000 Chrysler... • Answered on Mar 06, 2019
0helpful
1answer

Why when i turn the key to start car l get nothing?. i have power

check the main fuse in the engine compartment fuse box , the 100 amp , if this is ok and your sure the battery is fully charged and does actually hold the charge then i'd say it was the starter motor , do the dash lights illuminate etc ?
3/6/2019 11:05:59 AM • 2000 Chrysler... • Answered on Mar 06, 2019
0helpful
1answer

How to disarm 2000 Chrysler 300m with no fob

The alarm operation is a function of the body control module. I'm not aware of any owner procedure to disable it. You could disconnect the horns, but that creates other problems. If you lock the car manually with the locks on the window ledge, NOT the electric switch, NOT the remote and NOT with the key, the alarm system is not supposed to activate and should not trigger. The red light on the dash will not be flashing if the alarm is not set. It isn't a perfect solution but it may be a workaround. Unlocking the doors with the key is supposed to shut off the alarm. Have you tried that? Do your remotes work consistently for other functions? Maybe the batteries are getting tired. 24 7 Locksmith Williamsville Ny 716 200 1030 Locksmith Williamsville Ny 26206451-dnc2e1izs3stmwduc0sbwiqp-1-0.jpg
3/6/2019 11:05:40 AM • 2000 Chrysler... • Answered on Mar 06, 2019
0helpful
5answers

Headlight bulb replacement on chrysler 300m

Parts Required: Change all the lights at once, it is not worth the anguish of doing this over and over again
2 low-beam lights, 2 high-beam/running lights, 2 parking lights - part nos in the owners manual


A can of diet coke to clean the battery terminals is also recommended. *optional



Tools required

Ratchet set : 10mm, 7mm, 6mm sockets
Extension 12"
Large Flat screwdriver, small 4" flat screwdriver and a pair of pliers
Flash-light
12" Magnetic tip telescoping bit

Surgical gloves

Battery terminal cleaner * optional



Step 1:

First take off the plastic cover that cover that is across the front of the engine compartment. 6 push pins hold it in place, Use the long flat screw driver to pry them up and use the pliers to pull them off.


Gently take the plastic cover off and set it aside.


Step 2:

Next you will see 3 push pins that hold the front grill to the engine housing, using the long flat and a pair of pliers pull the 3 push pins out.


Step 3:
In the upper area of each wheel well, you will see a large 2.5" rubber grommet. Pull the rubber grommet out



Step 4:
Locate a 6mm bolt head that is driven vertically upwards. It is not visible looking at the wheel well. You have to lay down on the floor and you will find it about a foot below the grommet and at the edge of the fender. Use the the ratchet to remove this bolt headed screw. It is about a 1.5" long. Do this for both sides before going to the next step


Step 5:

Start with the passenger side as it is easier. Use the flash light and peer into the fender area from the engine compartment. You will see a nut on a bolt, and a plastic fastener.
Use the 10mm socket on the 12" extension. Insert it into the hole where the grommet was, and guide the socket on the nut head. It is about an 1" long. Be careful as you take it off, else you will be fishing for the bolt in the fender.

Step 6:
Pull on the plastic fender in the front till the bolt head and the fastener exit the fender. This has to be repeated for each side.

Step 7:
Locate 8mm bolt heads on top of the light assembly. Note it is not the Philips head - they are to level the lamps. Before undoing the bolts, check the spirit level on top of the lamp assembly and make a note of the bubbles position. You will need this when you put the assembly back. Undo both bolts, they have about an 1" of thread on the top and then you have to pull it up physically or with the use of the pliers

Step 8:
Pull the headlight assembly out - gently. Don't scratch the paint work and don't damage the rubber molding around the light assembly.

Step 8a*: If you see any salt build up on the battery terminals, pour diet coke or pepsi on the terminals, this neutralizes all the salt. Then pour some water to clean the gunk and then with a paper towel dry it. Be careful with the paper towel, as it contains sulfuric acid and is corrosive, put in in a garbage bag immediately. If you feel it has come into contact with your skin, was vigorously before continuing.

Step 9:
Note the position of the connector before you do anything. Turn the retaining rings holding each bulb counter clock wise. When you do this the bulb assembly and the connector will pull free. Two instances of this. Remove assembly, and place securely on a table

Step 10:
Locate the parking light below and turn the connector clockwise as you are looking over it. Pull out the old bulb and replace it. Do this for both sides. Turn on the parking lights to ensure they work, try the signals too. No sense it putting it all back together and nothing works. Replace the holder and bulb in reverse order. Note the unit should fit in nicely and rotate smoothly as you turn counter clockwise this time.

Step 11:
Using the 4" flat screwdriver, lift the locking pins gently and push the bulb out, Start with the low beams. Low beam has only 1 filament, high-beam/running light has 2 filaments. Put on the pair of surgical gloves, and open the pack of new bulbs, push the bulbs into the empty sockets, until the locking pins click into place. Change the low-and high beams.

Step 12:
Insert the bulb with the connector in the position you noted in step 9. Slide the mounting ring and then lock it into place by turning it clock-wise as you are looking at it from the rear of the assembly. Repeat this for both the high beam and low beam. Slide assembly back into cavity. Repeat this for the other side. Test the bulbs light correctly

Step 13:
Gently push back the front plastic so that the bolt and the plastic stud enter the fender. Pay attention to ensure that the fender lining sits correctly. Using the 12" ratchet extension and the 10mm socket mount the bolt back on and tighten. Do this for both sides

Step 14:
Using the ratchet mount the 6mm fastener on to the fender. Do this for both sides

Step 15:
Mount the jack screws on top of the headlight assembly. Tighten till the bubble in the spirit level returns to the original position. Don't push the bolt past its maximum. If it doesn't return to the original level, loosen and adjust the headlamp assembly and re-tighten. Do this for both headlamps.

Step 16:
Replace the 3 push pins that hold the front grill to the engine compartment. Replace the large plastic panel that was removed in step 1 and remount it using the 6 push pins.


Voila - you have changed all the bulbs on the front of the 1999 300M.

Estimated time:
Novice 2 hours
Advanced 1 hour
Expert 45 mins

If you found this helpful, a quick note to the author George and Anna at [email protected] would be appreciated.
2/13/2019 8:52:10 PM • 2000 Chrysler... • Answered on Feb 13, 2019
0helpful
2answers

Car smells like gas and has trouble starting

This sounds like your evaporative emissions system acting up. Has the check engine light come on? There should be a charcoal cannister that filters the vented air/fumes from the fuel tank. If a vacuum or vapor line is broken, or removed.. or if the charcoal canister is depleted, you'll get the gas smell.
6/1/2018 4:56:03 PM • 2000 Chrysler... • Answered on Jun 01, 2018
0helpful
1answer

2000 300m transmission shifting problems

ecp/pcm reprogram / update If you need further help, reach me via phone at https://www.6ya.com/expert/james_9c1b039055413ffa
10/3/2017 3:44:16 PM • 2000 Chrysler... • Answered on Oct 03, 2017
0helpful
1answer

Chrysler 300m, Oil lite comes on then engine ticks then cuts off

Is an oil pressure problem, inside the oil pan have an pump strainer , maybe its dirty clean
5/17/2017 5:32:46 PM • 2000 Chrysler... • Answered on May 17, 2017
0helpful
2answers

Heater temp on high only bows luke warm air after driving. A/C works just fine.Plenty of cold air from it

heater blows cold air idle chrysler 300 Questions & Answers ...

www.fixya.com > Forum > Tags
Find solutions to your heater blows cold air idle chrysler 300 question. ... blow warmair for a few mins then back to luke warm. i replaced thermostat ... HEAT BLOWSCOLD AIR WHEN IDLING ONLY GETS HOT WHEN START DRIVING ... About 15 minutes after driving the diver side vents start blowing straight cold air but the ...

Heater only works when pressing the gas? - DoItYourself.com ...

www.doityourself.com/...repairs.../459521-heater-only-works-when-pres...
Nov 3, 2011 - When I press the gas, the air from the vents is nice and hot. .... So am Idriving a car with a ton of problems, or could the power steering ... Just anotherquestion, when warmed up does the engine temperature ... When the heater is on and I'm not pressing the gas pedal, luke warm air blows from the vents.

Heater blows cool air when stopped and warm air while ...

https://www.reddit.com/.../heater_blows_cool_air_when_stopped_...
RedditFeb 12, 2014 - Heater blows cool air when stopped and warm air while driving 2008 Kia Spectra (self. ... just fine but appears to blow cool air when I was stopped at a stoplight. ... My temp gauge would also be pegged high when at idle / low RPM. ...thermostat only blocks coolant going to the radiator, and the heater core, ...Missing: 300m ‎luke

Why is My Car AC Blowing Hot Air? - BlueDevil Products

gobdp.com/blog/car-ac-blowing-hot-air/
4/30/2017 11:31:39 AM • 2000 Chrysler... • Answered on Apr 30, 2017
0helpful
3answers

Vehicle shimmies when brakes are applied

Loose tie rods that is what my problem was when my car did that. What happens is when you apply the brakes the tie rods move in and out
5/28/2016 12:45:58 AM • 2000 Chrysler... • Answered on May 28, 2016
Not finding what you are looking for?
2000 Chrysler 300M Logo

623 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Chrysler Experts

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8991 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6963 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

15008 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

300M Chrysler

  • 300M Chrysler

Most Popular Question

2000 300m transmission shifting problems

  • Cars & Trucks
Loading...