20 Most Recent 2001 Jeep Cherokee Questions & Answers

warped heads will cause this...if it over heated badly thats going to be the problem

2001 Jeep... • Answered on Feb 11, 2018

I would need to hear this noise to help, sorry, but you need a shop to look into this.

2001 Jeep... • Answered on Feb 07, 2018

check the cable to the ecm they made them pull down on the pins right from the factory and messes up lots of stuff , loosen the cable and see if that helps , fixed all kinds of problems in my jeep

2001 Jeep... • Answered on Nov 10, 2017

Try unplugging the passenger door module from the wiring harness. Module may be bad. I see one screw holding it with tabs at the other end. You should be able to pull it up without removing the door panel. I see there are modules online for less than $40.

2001 Jeep... • Answered on Nov 04, 2017

Check to ensure the front reservoir pump is connected and receiving power. Is the fuse bad? It is possible the pump inlet is clogged. This would require removing the reservoir and flushing it. If this is a washer with an external, self-priming pump, is the pump uptake tube in the cap missing?

2001 Jeep... • Answered on Nov 01, 2017

light switch is bad,they have a history of it,and also blinker switch

2001 Jeep... • Answered on Oct 12, 2017

The windows are controlled by a computer module known as the BCM, have the dealer perform a self test of the module with a special scan tool.

2001 Jeep... • Answered on Sep 01, 2017

Yeah Michael, try tightening the belt on it just a bit tighter. You may not hear slipping belt but it is slipping. But then you say it doesn't work at all at idle, sounds a bit more like a week pump or is too low on fluid. For fluid, just use GM trans fluid, it's cheaper and the same thing as expensive tranny fluid.

2001 Jeep... • Answered on Jul 11, 2017

Head gaskets do not make black smoke it is white and smells sweet, is that the case?

2001 Jeep... • Answered on Mar 31, 2017

Is this using europeon lighting or that funny american thing of stop lights indicators all in one .

2001 Jeep... • Answered on Mar 14, 2017

If no spark at the plugs, engine cranking, did you check primary voltage at the coil assemble, dark green wire with orange tracer, engine cranking, use a test lite on the wire check for voltage. If no voltage that will lead back to asd relay. There are some fuses involved. I believe the computer has to see both the cam and crank sensor signals or it won't ground the asd relay. All I can do is make testing suggesting. cherokee asd relay-m5cnn2lotweryjtsi2x53sss-2-0.jpg

2001 Jeep... • Answered on Mar 10, 2017

Greetings john ingall Dec 12, 2016 piggy backers.. old. why not start a fresh post for only your car and not mix up other symptoms.did play with the CMP or CKP. then cause p1391.oops...a daisy.... you did it wrong.Id not attack coil rail until the 1391 is cured, not me.1: scan it ? post all DTC now.2: DTCs trouble codes..????3: is the ASD dropping off line, while running? (a key fact to know)4: ever get a tune up this decade?????5: spark gaps correct , to factory spec, and kept here doing repeated service? )6: Do the scans show the IMMO tripping the ASD off line????there are 8 reasons for ASD to trip , and cause a stall, all 8 are reported !there are 50 other reasons for stalls, called misfiring...the service manual is clear (p035x's)Peak primary circuit current not achieved with maximum dwell time.This means that the PCM charged to coil fullyand the current was way too low.that means it found (out of spec) current.even zero current, means coil burned up or the transistors to it.gee, id have the rail off and check each coilthere are 6 coils, 3 primary and 3 secondarythe SM cover this test, as all do so read it.it can also be bad connections(wires) to same.(crude, 5ohm pri, 20k secondary ohms) OUR 4.0l HAS A RAIL PACK, COILWITH 3 COILS inside, and uses wasted spark to fire all 6and if one coil fails you will loose, 2 cylinders, due to series HV wring, unless 1 wire shorts, but if one opens you loose 2 cylinders.( Kirchhoff's laws 1; an open in series circuit flows no current, so both spark plugs go dead.unless rich and super lucky , try using a scan toolwhen the engine misfire, or stalls.and report all errors seen, DTCs, a win/win. the schematic, see F18 fuse , the coil packsuper simple no? ,yes, but not on PCM end. (Ask)here.dac293a8-5823-4d8e-8165-130c10d9e961.jpg

2001 Jeep... • Answered on Jan 27, 2017

IT WAS the oil cooler leaking

2001 Jeep... • Answered on Jan 21, 2017

Your sensor is located next to the crankshaft pulley. it is halfway into the block and, the housing will have wire clips protruding outwards. it should be around the top left or right side of the pulley.

2001 Jeep... • Answered on Nov 22, 2016

check fuse first

2001 Jeep... • Answered on Aug 09, 2016

On hood latch..where cable goes in..there is a hole there..trip it back..or take the 3 bolts away from latch

2001 Jeep... • Answered on Jul 09, 2016

Try and get a hold of the cable at any location , You will have to have a pair of pliars , and it usually take a good pull. Short of that is the only way is going straight to the latch, after removing the grill.

2001 Jeep... • Answered on Mar 07, 2016

Not finding what you are looking for?
2001 Jeep Cherokee Logo

924 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts

Greg Bernett
Greg Bernett

Level 3 Expert

2993 Answers


Level 3 Expert

4376 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14869 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Cherokee Jeep

  • Cherokee Jeep

Most Popular Question

recently purchased 2001 jeep cherokee

  • Cars & Trucks