2000 Jeep Grand Cherokee - Page 4 - Answered Questions & Fixed issues

If every thing looks the same there should,nt be a problem but first check with a transmission re-build shop.only a phone call away.

2000 Jeep Grand... | Answered on Apr 26, 2016 | 100 views

pedro; piggy backs on Jun 27, 2014 post
in 2 places. cab box called JB (junction box)
and under hood called PDC> (power distribution box)

post a symptom,
and ill point to a fuse.
JB on usa LHD car is at driver left ankle.
is car usa car? LHD = left hand drive.

and what size engine?8c663aa2-22d0-4068-be64-592948c7b4bc.jpg24713078-35o2neab0gfd3xxniicphqo5-1-2.jpg


2000 Jeep Grand... | Answered on Apr 09, 2016 | 119 views

First remove and clean battery cables and battery posts with a wire brush or sand paper. Make sure battery is charged and check to see if it starts. Then check battery condition and charging system. The problem could be cables, battery, or alternator. Check them in order and repair or replace as needed. Check cables, battery, belts(tension and condition), and charging system in order. Do this because bad cables will give false readings for other tests and so on.

2000 Jeep Grand... | Answered on Mar 23, 2016 | 470 views

why not do what it says to do?
not sure what you saw there are many coolant errors that are possible on this car.
but if RAD level low , that means ...
the side bottle (plastic expansion tank) is low.
it has a sensor there, if the coolant levle there is ok . (i bet its NOT)
then replace this sensor, or the wires fell off.
or clean it , if it fibs. clean it, and now works.

the parts are all shown in one or 2 places
the online dealer parts pages, jeep dot com
and here
lets turn to the correct page
click WJ


2000 Jeep Grand... | Answered on Mar 02, 2016 | 155 views

If you have blown the bearings, eventually they melt and plug the oil holes, so that the oil pressure pegs. Don't drive it at all.

2000 Jeep Grand... | Answered on Feb 11, 2016 | 182 views

The brake light switch will be open circuit when the brake pedal is not depressed and will have a closed circuit when depressed. IE/ switch off when the pedal is up and switch on when the pedal is pressed. You will need a multimeter to check or you can use a 12 volt globe or voltage tester. Power on 1 side of the switch when off, both sides when closed or on.,

2000 Jeep Grand... | Answered on Feb 05, 2016 | 296 views

what is a CAN?

my guess you meant "how CAN i replace my A.C compressor."

RTM ,read the manual chapter 24
its all there, just read and then ask questions.




2000 Jeep Grand... | Answered on Jan 31, 2016 | 314 views

Is it leaking externally that you see? If so, you may have leaking freeze plugs on the engine block or cylinder head. If it is not external, then check the exhaust. Are you getting white smoke? Does the exhaust have a sweet smell? You could have a cracked cylinder wall, cylinder head, or blown head gasket. Check the floor inside the vehicle. Is it wet anywhere, especially passenger side front. It could be a leaking heater core. If all else fails, have the system pressure tested by a mechanic to find the source of the leak. Some can be very hard to detect.

2000 Jeep Grand... | Answered on Jan 26, 2016 | 227 views

is that a question?
what 4wd system do you have?
quadra drive, or quadra trac 1 or 2?????
apples and orange different; do tell?
also tell what tires are touching, pavement,ice or dirt.

here is the book, wj, free posted over 200 times, here.


2000 Jeep Grand... | Answered on Jan 20, 2016 | 598 views

i guess you meant HOW CAN I program? (key word "I")
is car USA car?????? (our rules are UNIQUE)
the operators guide on all jeeps cover this.
posted this 100s of times here.
there are lots of rules related to this.
first off most newer cars, you need 2 keys to make a 3rd.
and has a 8 key limit,
and new key must be new, as used ones will not program.
tricky huh? and gets worse in time, the 2010 you cant do at all.
my 08 can do. and did.
the car came with 2 keys, lost one?
that be first first.
lost operators guide, even look yet?

WJ jeep year 2000
ill read the book for you.
veh. theft security chapter.
chapter 8q in the FSM.
page 7 , "customer method"
ill see if i can paste it here, (found it in 10 seconds)

quote, real FSM
The Customer Learn feature is only available on
domestic vehicles, or those vehicles which have a
U.S. country code designator. This programming
method also requires access to at least two valid Sentry
If two valid Sentry Keys are not available,
or if the vehicle does not have a U.S. country code
designator, the Secured Access Method must be used
to program new or additional valid keys to the SKIM.
The Customer Learn programming method procedures
are as follows:
(1) Obtain the blank Sentry Key(s) that are to be
programmed as valid keys for the vehicle. Cut the
blank key(s) to match the ignition switch lock cylinder
mechanical key codes.
(2) Insert one of the two valid Sentry Keys into the
ignition switch and turn the ignition switch to the
On position.
(3) After the ignition switch has been in the On
position for longer than three seconds, but no more
than fifteen seconds, cycle the ignition switch back to
the Off position. Replace the first valid Sentry Key in
the ignition switch lock cylinder with the second
valid Sentry Key and turn the ignition switch back to
the On position. The second valid Sentry Key must
be inserted in the lock cylinder within fifteen seconds
of removing the first valid key.
(4) About ten seconds after the completion of Step
3, the SKIS indicator in the instrument cluster will
start to flash and a single audible chime tone will
sound to indicate that the system has entered the
Customer Learn programming mode.
(5) Within sixty seconds of entering the Customer
Learn programming mode, turn the ignition switch to
the Off position, replace the valid Sentry Key with a
blank Sentry Key transponder, and turn the ignition
switch back to the On position.
(6) About ten seconds after the completion of Step
5, a single audible chime tone will sound and the
SKIS indicator will stop flashing, stay on solid for
three seconds, then turn off to indicate that the
blank Sentry Key has been successfully programmed.
The SKIS will immediately exit the Customer Learn
programming mode and the vehicle may now be
started using the newly programmed valid Sentry
Each of these steps must be repeated and completed
in their entirety for each additional Sentry
Key that is to be programmed. If the above steps are
not completed in the given sequence, or within the
allotted time, the SKIS will exit the Customer Learn
programming mode and the programming will be
unsuccessful. The SKIS will also automatically exit
the Customer Learn programming mode if it sees a
non-blank Sentry Key transponder when it should
see a blank, if it has already programmed eight (8)
valid Sentry Keys, or if the ignition switch is turned
to the Off position for more than about fifty seconds.
NOTE: If an attempt is made to start the vehicle
while in the Customer Learn mode (SKIS indicator
flashing), the SKIS will respond as though the vehicle
were being started with an invalid key. In other
words, the engine will stall after about two seconds
of operation. No faults will be set.
NOTE: Once a Sentry Key has been programmed as
a valid key to a vehicle, it cannot be programmed
as a valid key for use on any other vehicle.
end quote.

got all that?
if confused, ask any ASE shop in USA for help
they CAN DO !

2000 Jeep Grand... | Answered on Dec 26, 2015 | 228 views

Autotmatic transmission messing up?

A/T can mess up vast ways.
not up shift.
not down shift
do so too early or late.?
scan it yet? that be first after checking ATF levels.

buy or rent a scan tool, drive and see if there are DTC errors
or get car serviced.
only 2 ways,,,,, toss coin?

2000 Jeep Grand... | Answered on Dec 26, 2015 | 152 views

how high? name a VALUE is F or C?
and what does, engine or transmission
scan it to see that fact?> or just the dash guage?
do tell what you saw ,exactly.

2000 Jeep Grand... | Answered on Dec 26, 2015 | 182 views

why not post the code and not make us guess.???
no, it didnt fail again, someone guessed wrong.

take car to any ASE shop or transmission shop and win.
they will do diagnosis and find the real cause.

no code, no joy.

2000 wj

RTM yet,

see those pages on DTC errors. p07xx errors. and friends
and the statements on how to test further.....

2000 Jeep Grand... | Answered on Dec 26, 2015 | 137 views

So it's a Jeep. This gives the solution. You have a fuse under the dash that is blown.


2000 Jeep Grand... | Answered on Dec 24, 2015 | 259 views

we cant guess which 4wd option you have.
why not RTM

see this. WJ jeep
its all there.
part time 4wd or full time... cant guess it ever.
something TRAC..... what is something....?????????

2000 Jeep Grand... | Answered on Dec 11, 2015 | 244 views

you meant ENGINE pan or transmission?
or is that word "PANEL". (one N)
parts prices and labor
all vary by location
why ask the blind this
ask your mechanic.... (only this works)

did you mean the dash oil change warning lamp is on.?
why not just stated whats wrong first.... so we can be on same page.

2000 Jeep Grand... | Answered on Dec 11, 2015 | 66 views

Your fan on belt could be electric only comes in when engine heats up or

2000 Jeep Grand... | Answered on Dec 02, 2015 | 554 views

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

4,469 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Jeep Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides