Top 20 2000 Jeep Grand Cherokee Questions & Answers

https://www.fixya.com/cars/r26142776-want_bypass_vehicle_security_system ..

sorry not understanding the Azc fault please enlighten me as to what it is

The ignition module is located underneath the distributor cap, while the ignition coil is mounted typically on the engine block on the same side about 6-9" away. The center spark plug wire will lead to the coil. The module can be found by removing the distributor cap, there is a wiring harness that plugs into it.

Jeep Cherokee Questions - where is the ignition control ...

Try bleeding the slave cylinders.

I would say the alternator. The fluctuations when it is running indicate that the regulator inside the alternator is worn out. The overheating is probably because the cooling fan is not running fast enough or at all.

Your only problem friend, is the temperature sending unit/sensor. Upon cold start, this sensor wil tell the computer to go into cold start mode putting a bit more fuel in and raising the idle a bit to keep it running when cold without using the throttle. Replace that sensor and your good to go. Makes sense, right?

I have seen jeep TPS - throttle position sensors cause a surge like you describe , but not with injector circuit code's . The PCM - engine computer controls the injectors by supplying a PWM - pulse width modulation ground . Checking the electrical circuits for those injector's would be the thing to do . Do you know how to test electrical circuit's ? Plus checking the drivers (transistors ) inside the PCM should be done . Could be a wiring or computer problem or even those injectors could be failing . How to Check Fuel Injector Resistance with Multimeter How to test fuel injector circuit with basic tools open control wire

Try squeezing as you pull, be gentle

Take some lube spray and spray the entire lock assemblies. You may need to take the door panels off to do a good job. With the panels off you can watch and see what is happening.

Rather then guessing an just replacing parts , have a qualified repair shop hook up A/C manifold gauges an check the system . Can tell you what's wrong in just min. (it is only blowing slightly cool air. I suspect it is the orifice/expansion tube and want to know if I can change it out myself or reair it.) Don't suspect , that's guessing . test don't guess . Are the A/C pipes going in through the fire wall cold ,have ice on them when A/C is on ?

You just go to the link I attached I'm sure you will get the solution of your problem 2000 Jeep Grand Cherokee

back firing ( explosions in the exhaust) can be from fuel mixture too rich and unburnt fuel is getting to the hot exhaust possible causes for that are excessive fuel pressure , leaking injectors ,leaking injector seals backfiring through the inlet manifold can be calve timing, ---cam advance servo-- valve staying open ---valve clearance , problem hydraulic cam follower , incorrect firing order for the plug wires, crank/cam position sensors or wiring IN this country there is a joke about jeeps Santa was late with the presents because he bought a jeep ( jeep add about Santa buying a jeep released by jeep) Don't send it to a scrap yard as there are people who can fix jeeps

You probably have a poor earth on a rear light cluster, if you can find the earth wire ( often goes to the body close to the lamp) that will be the problem and it will need cleaning or a new terminal putting on.

Stop leak can cause the radiator ports to get clogged. But if your car isn't getting heat, it's probably your heater core. The heater core is usually burried in the firewall between the engine and where you or your passenger put your feet

it is as hard as it looks, the book says to take it to the dealer,

not sure what type vehicle we're talking about here, although you can lube up the rack and pinion or grease up your upper, if so equipped, and lower ball joints.

when did it make the clicking. was it when turning sharp, if not it is another issue

it could be a problem with the wiring with the sensor. You would need a multi-meter to check the wiring. Diagnostics cannot tell if the sensor is bad, only that the information sent does not agree with what should be reported.

How about plugs wires.