2000 Jeep Cherokee - Page 8 - Answered Questions & Fixed issues
Engine light stays on code p1494
P1494 code is a leak detection pump switch or mechanical fault, leak detection pump switch does not respond to input. The leak detection pump (if equipped) is located under the air filter housing on models through 2001. Check if the vapor and vacuum lines are securely connected to the leak detection pump or a diagonstic trouble code my be set like this. The leak detection pump switch may be bad and need replaced.
9/29/2011 2:10:06 PM •
2000 Jeep...
•
Answered
on Sep 29, 2011
•
1,325 views
Interior lights stay on
either the lights are turned on manually from the headlight/interior light switch, or you have a defective door switch that is telling the module that a door is open, or you have a door that is open, or your module that controls the interior lights is defective. I would start with the simple things, I would make sure all doors are closed. If they are, then check the headlight/interior switch to make sure the interior lights are in the off position, then check all of the door switches. They are simple normally closed push button switches that should be mounted on the car frame near the door hinges.
9/24/2011 1:48:17 PM •
2000 Jeep...
•
Answered
on Sep 24, 2011
•
558 views
The transmission cooling fan stays
Some vehicles do that and it's OK. It is cooling down the transmission fluid. Once it reaches the set temperature, it will shut off.
9/14/2011 5:54:45 PM •
2000 Jeep...
•
Answered
on Sep 14, 2011
•
87 views
Service required trouble light on
There are codes stored in the PCM. Go to an Auto Zone (or possibly other parts stores) and have them hook up a code reader. Its usually a free service.
9/11/2011 4:48:16 AM •
2000 Jeep...
•
Answered
on Sep 11, 2011
•
21 views
Cherokee will not start until
Might have to reset the codes on the computer. Take the + battery cable off the battery and reconnect it afer 5 minutes. Next try to start the engine without holding the gas petal down, it should start and run rought till the computer resets itself. If engine stops, restart the engine and hold the gas petal down and give it enought gas so it will run smooth, it may take 5 minutes or so for it to smooth out and run at idle speed. If this did not fix the problem, check for a vaccum hose that may be off some where on the engine
9/5/2011 3:16:58 PM •
2000 Jeep...
•
Answered
on Sep 05, 2011
•
260 views
Seperated harmonic bal how to
If you are talking about the rubber in the balancer itself. You can not do this. Balancers are fairly inexpensive. I would get one at a junk yard. I think they are about 40.00 dollars new.
9/3/2011 6:16:26 PM •
2000 Jeep...
•
Answered
on Sep 03, 2011
•
69 views
Can you replace the front left window lift motor
You folks really need to learn to give more detailed info when you need help. The answer is, "it depends". If you have the small Cherokee, the answer is no. If you have the Grand Cherokee, the answer is yes. You will have to remove the motor and regulator to get them apart.
Charlie
8/19/2011 11:30:08 PM •
2000 Jeep...
•
Answered
on Aug 19, 2011
•
40 views
Have a leaky stablizer shock.
Its not hard to replace, theres a bolt and nut on each end, remove them and out comes the shock, one end goes to the center link and the other end to the differentail housing on a bracket, it will take about 15 to 30 min to replace it, good day
7/30/2011 1:50:04 PM •
2000 Jeep...
•
Answered
on Jul 30, 2011
•
46 views
Car will turn over fine but won' start, as if
but is the fuel pump working.if you remove the air snorkel and spray intake cleaner into the intake while someone tries to start the car and it starts then you have a fuel problem.either the pump,plugged fuel filter,fuel injectors not working,dirt in the fuel system.check the fuel pressure if it doesn`t start when spraying cleaner into the intake.
7/7/2011 5:59:27 PM •
2000 Jeep...
•
Answered
on Jul 07, 2011
•
207 views
Engine Cooling problem 2000 Jeep Cherokee 4 cyl
Although the 4 cylinder is too underpowered to have air conditioning in my opinion, it still shouldn't overheat within 10 minutes unless something is wrong. If your Jeep doesn' not overheat when you are driving WITHOUT AC on then your compressor might have a problem and causing the engine to work too hard to turn it.
But if it overheats without the AC on, then the first thing you need to do is check the cooling fan and see if it operates! There has been a lot of problems with the cooling fan relay on this model. If that isn't it, then move to changing the thermostat and checking the water pump.
7/3/2011 3:11:39 PM •
2000 Jeep...
•
Answered
on Jul 03, 2011
•
275 views
We can not find the
That isn't even possible, if you looked for it
Explain !!!
What engine?
Put it into your search engine
you will see a picture
6/12/2011 1:38:19 AM •
2000 Jeep...
•
Answered
on Jun 12, 2011
•
27 views
Csnt get serpentine belt off I'm trying to
There are two bolts if it is like the older model, you have to loosen the bolt on the front of the pulley and then the tension bolt. If you don't loosen the bolt on the front of the pulley the pulley can't move when you turn the adjuster bolt.
6/2/2011 2:55:54 AM •
2000 Jeep...
•
Answered
on Jun 02, 2011
•
67 views
I put every new parts such as both 02 sensors and
The problem is that you need to understand OBD 2 Systems first
Then diagnose whatever the issues were.
You do not just put parts on any vehicle hoping to resolve an issue.
You only replace any part when it was found to have failed
or reaches a certain milage and is due to be replaced.
In most cases that will require the use of a volt meter or an
oscilloscope, as well as system knowledge.
There could be 20 things that could cause a problem
You have to use the codes you get,if any, to start a process
of elimination.
5/22/2011 11:38:27 PM •
2000 Jeep...
•
Answered
on May 22, 2011
•
46 views
When i use the left
That's consistent with a signal switch (multi function switch) failure. It's part of the signal arm and isn't that difficult to replace. (covers on the column need to be removed). Instructions for that can be found in chilton or haynes manuals but if you have any mechanical aptitude you likely can just look at it and see how it comes out.
5/21/2011 3:06:18 AM •
2000 Jeep...
•
Answered
on May 21, 2011
•
84 views
Thow to take off door
first you have to remove dead plugs on door handle and remove screws another screw on door opening handle and you have to disconnect 2 metal pins behind that and look all around the door panel sides and under should have several rivets make sure no any screw and rivets left on door panel pull door panel foward and pull it up dont go too hard dont damage door panel conections for proper reinstallation. before removing door panel from the door dont forget disconnect cable connections from window and door lock switches.good luck
5/7/2011 12:56:52 AM •
2000 Jeep...
•
Answered
on May 07, 2011
•
165 views
Not finding what you are looking for?