20 Most Recent 2006 Jeep Commander Questions & Answers


Need more info, is your light on on the dash? Are the brakes working fine?

2006 Jeep... | Answered on Oct 05, 2019


2006 Jeep Commander 5.7L Hemi, Owner and car-mechanic here...I do not know what engine you've got. But the have Hydraulically-Operated cooling fans on them, run off of the Power Steering system. Mine does not like traffic or idling, she runs cooler at 70-80MPH! You have fan, fan solenoid, and hydraulic lines to the fan.

2006 Jeep... | Answered on Oct 02, 2019


Was the battery replaced and this occured afterward?

2006 Jeep... | Answered on Jun 13, 2019


If it's a manual seat mechanism, search for the lever/latch that releases the seat on its track. If power seat, check the fuse for that circuit and work from there.

2006 Jeep... | Answered on Mar 30, 2019


do you have a rear heater ? if so check for a leak ... or have you done any aftermarket stereo install lately where any wires where run through the firewall, look for any places water can splash threw a hole in the sheetmetal... have seen it many times, all you have to do is have a hole and then drive trough a puddle or two... please rate my help...thanks

2006 Jeep... | Answered on Mar 30, 2019


can be many things, even bad head gasket.
but bad radiator,
we use our $15 IR thermo gun , and measure top and bottom of
each rad tube, and find the dead ones.
in 5min work.

or run the rad leak down test, to see head gaskets are good.
you never said
which engine,
Fan works when its over 220f degr. it must
or fan is bad, or its controls. (tests with voltmeter easy)

2006 Jeep... | Answered on Mar 01, 2019


Please be more specific with your question

2006 Jeep... | Answered on Jan 16, 2019


no it will most likely be a blocked drain pipe that goes into the engine bay from the A/C and drains the condensation created by your car's air conditioner. A mechanic workshop can do a blast of compressed air by your mechanic and free the blockage takes about 30 seconds to do with a car hoist.
If it is humid conditions the problem will be much more and you might find the front demister won't work due to water sitting on top of the Air conditioner. It will heat this water and blow steam on your window.

2006 Jeep... | Answered on Feb 26, 2018


disconnect any wires going into the door
undo the door hinge bolts ( have a friend hold the door while you do this
have him hold the new door in place while you refit the bolts to the hinges
adjust the hinges under the bolts jut fitted until the door locks easily in place
reconnect the wires
Job time --1/2 hour

2006 Jeep... | Answered on Jan 13, 2018


Be sure the blend door is not stuck before replacing the blend door actuator. Otherwise the actuators will continue to strip out.

Here is a calibration procedure I found that may/may not be useful:
Door calibration function for MTC system per Chrysler service manual.

1.Turn the ignition to the ON position.
2.Turn the blower motor control to the OFF position.
3.Press and hold the EBL "rear window defrost" switch down and turn the blower motor control on. Continue to hold the EBL switch down until the EBL status indicator begins flashing, then release the mode switch. While the test / function is running the EBL status indicator will flash once per second. If the test / function passes, the EBL status indicator will stop flashing. If the test / function fails, the A/C and EBL status indicators will flash alternately.

While the test is doing it's thing you will hear the doors open and close as it calibrates the system.


manual HVAC motor calibration

2006 Jeep... | Answered on Jan 10, 2018


Sounds like a belt may be slipping or bad water pump. Overheating and loosing heat at lower RPM sounds like your not moving enough water through the cooling system, at higher rpm moving just enough water moving to be happy. Check water level and belt tension check bad thermostat not fully opening at temp then water pump. if it were just overheating I would look at the fan but loosing heat is definitely lack of water through heater core.

2006 Jeep... | Answered on Dec 14, 2017


pull the switch out use meter to see if you have 12 volts if so try to use a jumper wire on the switch if this works replace switch take switch to electric shop before going to dealer

2006 Jeep... | Answered on Dec 02, 2017


A dtc does not say to relace a part untill diagnostic procedure for said code is preformed . Do you know what a diagnostic trouble chart is ? Factory service repair info. is best .
https://www.obd-codes.com/p0335

2006 Jeep... | Answered on Nov 11, 2017


incorrect about the insulation
it will most likely be the climate control module that has failed and needs replacing as what the dealer has stated

2006 Jeep... | Answered on Oct 30, 2017


https://s21.postimg.org/6kfdcs4zr/integrated_power_module.jpg

Click on the link.
Integrated power module, under hood close to battery. Some makes and models have different names for bcm. Just my opinion.

2006 Jeep... | Answered on Jun 08, 2017

Not finding what you are looking for?
2006 Jeep Commander Logo

889 questions posted

Ask a Question

Usually answered in minutes!

Top Jeep Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Commander Jeep

  • Commander Jeep

Most Popular Question

change burn out light heat direction

  • Cars & Trucks
Loading...