20 Most Recent 2001 GMC Yukon XL Questions & Answers

0helpful
2answers

MY 2001 GMC YUKON XL WILL NOT START OR TURN OVER. I REPLACE A NEW STARTER AND BATTERY, WHAT ELSE NEED TO BE DONE. ITS SEEMS LIKE ITS AN ELECTRICAL PROBLEM.

A mechanic would check for voltage at the starter, the neutral safety switch, and the key switch. Then check the battery cables and ground connections.
11/14/2021 5:02:37 AM • 2001 GMC Yukon... • Answered on Nov 14, 2021
0helpful
2answers

My 2001 yukon front AC fan only blows on high

Replace the blower motor resistor located in the blower housing under the dash on the passenger side and you will be good to go.


360dreamworx_54.gif
12/7/2019 8:27:08 PM • 2001 GMC Yukon... • Answered on Dec 07, 2019
0helpful
1answer

Does a 2001 xl Yukon have two speed senors

Yes input and output sensors
5/2/2018 11:06:49 PM • 2001 GMC Yukon... • Answered on May 02, 2018
0answers
0helpful
1answer

Why does it take several tries before my 2001 Yukon Xl start? fuel pressure regulator?

By cycling the key and it starting, I would suspect the fuel pump. Sounds like low pressure.
1/12/2018 9:30:23 PM • 2001 GMC Yukon... • Answered on Jan 12, 2018
0helpful
1answer

The dash on my 2001 gmc yukon went out and the radio did too, why?

Yes I think there is a problem in radio or in cigarette plug check if the fuse are the same for both
12/14/2017 8:38:20 AM • 2001 GMC Yukon... • Answered on Dec 14, 2017
0helpful
1answer

I have a 2004 GMC Yukon XL and the rear passenger

check VEH STOP fuse in the instrument panel fuse box. If good, check for battery voltage in the bulb connector on the light blue wire with lights on. If no voltage, check for voltage in the rear junction box. Pull connector 4 and check for voltage on the terminal that connects to the light blue wire. If not voltage, you'll have to check the harness between the rear junction block and the underhood fuse block
10/13/2017 5:54:59 PM • 2001 GMC Yukon... • Answered on Oct 13, 2017
0helpful
1answer

All windows but drivers won't go up or down 2001 GMC yukon

If they sound like they are trying to do something it's not the lock out switch . But to be sure pulling out the switch an testing for B+ voltage to and from the switch . Plus pull the other door switches to see if they have B+ voltage and good grounds would be the thing to do.. If you don't know how to check automotive electrical circuits your best bet , take it to a qualified repair shop . Passenger Power Window Operation The passenger power window switches incorporate window up and down relays. The relay coil feed and supply sides are powered through the RAP fuse supply voltage circuit. The normally closed contacts of each relay is connected to ground. The load side of each of the relays are connected to either side of the power window motor through the power window up and down circuits. The up and down relay control circuits are connected to the normally closed contacts of the passenger window switch. These contacts are wired in series with the power window master switch, through the power window master switch up and down signal circuits and then to ground when the power window master is placed in the up or down position. This allows for the up and down operation of the passenger power window from the power window master switch. The center pole of the passenger power window switch is also connected to ground and will energize the relay when placed in the up or down position. Driver Power Window Operation The driver power window is unique from the passenger power windows in that it does not use window up and down relays. The driver power window is operated directly from the power window switch. The normally closed contacts of the switch are connected to ground and the center pole is connected to the RAP fuse supply voltage circuit. By placing the left power window switch in the down position, voltage is applied to the power window motor left front down circuit and to the power window motor. The other side of the power window motor is connected to ground through the normally closed contacts of the left power window switch through the power window motor left front up circuit and drives the window down. By placing the left power window switch in the up position the polarity of the motor is reversed and the motor drives the window up. Has circuit breaker for B+ power • PWR WDO CB 25A (fuse block) (System power for left and right windows 2-door vehicles. System power for LF and LR windows 4-door vehicles) • PWR WDO CB 25A (IP wiring harness junction block) (System power for RF and RR windows 4-door vehicles) Could be passenger door switch .
8/21/2017 8:38:48 PM • 2001 GMC Yukon... • Answered on Aug 21, 2017
0helpful
1answer

2001 GMC Yukon - Clicking noise from dash/steering

I was having a clicking noise from a actuator under the dash of my car, it was a blend actuator.. Years ago they used cable then vacuum hose and now a lot of vehicle us actuators (motor driven gate) to open and close the vents, A/C and heater ducts. I do not know for sure that is your problem but when mine went bad I would get a clicking noise sometimes it click for a few seconds after I turned the car off. Just a thought.
8/2/2017 1:31:58 AM • 2001 GMC Yukon... • Answered on Aug 02, 2017
0helpful
1answer

A/c is not blowing cold air in front but air is cool in the rear.

Hey M, the pressure could be nothing but "hot air" and not freon... (I had this same problem!!) I let off a bunch of pressure..(nothing but clear hot air!!) ..using a small flat punch..on the low pressure side... if freon on comes out right away..stop.. if nothing but hot air comes out.. keep letting it out until freon comes out,,, When mine started letting out freon,, I quit and tried the A/C again... and it has been working fine since.. Just my recent experience!!!!
6/27/2017 10:57:53 PM • 2001 GMC Yukon... • Answered on Jun 27, 2017
0helpful
1answer

01 Yukon Transmission Problem Come and Goes

Take it to a reputable trans shop. These transmissions are controlled by a computer. If this is a 2500 or 3500 Yukon, I bet it is equipped with the 4L80E transmission. These have a tendency to allow transmission fluid into the large electrical connector, and it shorts out wires and can make things go crazy. There is a way to silicone the leak and fix it(videos on YouTube) or a good honest shop can do it without replacing parts.
3/10/2017 7:18:04 AM • 2001 GMC Yukon... • Answered on Mar 10, 2017
0helpful
1answer

What wiring harness adapter do i need to get to install a new amp...

Contact this company, they are the go to pro's on car and truck audio. crutchfield.com
6/2/2016 10:48:02 PM • 2001 GMC Yukon... • Answered on Jun 02, 2016
0helpful
1answer
0helpful
1answer

Where is main accessory fuse

It's not the fuse. That fuse controls many different things. I would pull the A/C controller. Unplug it and plug it back in. If it comes on, It was corrosion at the plug. If not, I usually tear it down and fix the controller. Your best bet is to replace it, Unless you are into electronics and can solder very small components.
3/6/2016 7:27:28 PM • 2001 GMC Yukon... • Answered on Mar 06, 2016
0helpful
1answer

Has 358000 miles, just had leaks repaired. Twice since my oil pressure gauge reads no pressure but not all the time? Why

1. Oil Pressure Gauge Not Working You will notice this happens when your oil pressure gauge is not reading, whether the engine is turned off, idle or running. Try to step on the gas to rev up the engine. If the oil pressure gauge still doesn't change its reading, your gauge is busted. It's best to replace it as soon as possible because you won't have any idea if your car is already overheating or not. 2. Oil Pressure Gauge Reading Too Low When your engine is idle, the oil pressure gauge will have a low reading. When the engine starts running or when you're already cruising or on the freeway, your gauge's reading should have increased. If it stays on a low reading, then you now your oil pressure gauge is broken. 3. Oil Pressure Gauge Reading Too High Another common oil pressure gauge problem is when your oil pressure gauge is reading too high when your engine is idle or when it's turned off. Rep
10/24/2015 11:57:52 PM • 2001 GMC Yukon... • Answered on Oct 24, 2015
0helpful
1answer

My '01 Yukon xl dings while I drive... but when I break it stops nothing but the Change oil indicator is on is that why it's dinging?

There 2 wires connected to key ignition one must be loose
10/15/2015 6:56:40 AM • 2001 GMC Yukon... • Answered on Oct 15, 2015
0helpful
1answer

Brake lights and cruise control are not working?

you have a bad brake light switch
9/10/2015 3:30:26 AM • 2001 GMC Yukon... • Answered on Sep 10, 2015
Not finding what you are looking for?
2001 GMC Yukon XL Logo

677 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top GMC Experts

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6963 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8991 Answers

Ryan Lutton
Ryan Lutton

Level 3 Expert

1267 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Yukon XL GMC

  • Yukon XL GMC

Most Popular Question

several tries before 2001 yukon xl

  • Cars & Trucks
Loading...