20 Most Recent 1993 Ford Ranger SuperCab Questions & Answers

You didn't post your engine size so please pick the one that works for you....I'll post them all separately:

2.3L Engine The oil pumps are not serviceable. If defective, they must be replaced.
  1. Follow the service procedures under Oil Pan Removal and remove the oil pan assembly.
  2. Remove the oil pick-up and tube assembly from the pump.
  3. Remove the oil pump retainer bolts and remove the oil pump.
To install:
  1. Prime the oil pump with clean engine oil by filling either the inlet or outlet port with clean engine oil. Rotate the pump shaft to distribute the oil within the pump body.
  2. Install the pump and tighten the mounting bolts to 14-21 ft. lbs. (19-29 Nm)

WARNING Do not force the oil pump if it does not seat readily. The oil pump driveshaft may be misaligned with the distributor or shaft assembly. If the pump is tightened down with the driveshaft misaligned, damage to the pump could occur. To align, rotate the intermediate driveshaft into a new position.

  1. Install the oil pick-up and tube assembly to the pump. If there is a gasket between the pump and the pick-up, use a new gasket when installing.
  2. Install the oil pan as previously described.


1993 Ford Ranger... | Answered on Nov 17, 2019

Your distributer may be going bad.

1993 Ford Ranger... | Answered on Oct 13, 2017

I am a Ford dealer Tech and this is what cures this issue most of the time.

, Get a can of intake cleaner from any local parts store, not carb spray, intake cleaner, it is made by a company called CRC, remove the air intake hose to the engine, hold the idle high so the engine won't stall, then spray the can of cleaner into the intake while keeping the engine running, use at least 1/2 the can, shut down the engine and disconnect the battery for 5 minutes, then restart and complete a number of mixed driving cycles, town, freeway, stop and go etc., after a few days the problem will go away as the system will relearn to the clean intake.

1993 Ford Ranger... | Answered on Jun 16, 2017

Have you charged the ac. If so check the low limit sw. on the dryer it will cut the power to the compressor if the charge is low or if the sw. fails.

1993 Ford Ranger... | Answered on May 09, 2017

There may be a tool, or you jam a metal tool between two metal parts.
check these out:

Removing Stubborn Clutch fan Ranger Forums The Ultimate Ford Ranger...

Fan clutch removal

1993 Ford Ranger... | Answered on Apr 11, 2017

The "check engine" light is on to tell you that there is a trouble code stored in your truck's computer. Most parts stores will read the codes for you for free. Get that done, and you will know what part to replace.

1993 Ford Ranger... | Answered on Jul 15, 2016

What size engine v8 v6


1993 Ford Ranger... | Answered on Feb 29, 2016

More info would be helpful, but just going on what you said, I would guess your brake lights fuse is blown. The running lights and the brake lights are on different fuses, and when you turn the headlights on the rear running lights turn on as well, which you may be confusing with the brake lights. If you check and the fuse is not blown, I suspect you may have changed or had the brake lights changed recently and the bulbs were the incorrect ones. Hope this helps.

1993 Ford Ranger... | Answered on Nov 11, 2015

It is sometimes called a shift lock switch or park switch.

1993 Ford Ranger... | Answered on Mar 03, 2015

ive had this question before. It is under your center console where the cup holders are. up tworge the front, take the console off and you will see it a little square box silver in color with a wire harness plugged into it. hope i helped.

1993 Ford Ranger... | Answered on Jan 06, 2015

mark the balancer with a white paint marker on the TDC groove, there is a small plug over on the d/side inner fender has a small "dummy" plug plugged into it remove that from the wiring harness plug, loosen the distributor hold down bolt, connect the timing light by hooking the battery leads up to the battery and the other clamp over the #1 spark plug wire, crank truck up and squeeze the trigger on the timing light while trying to locate your paint mark on the dampener, then rotate the distributor in either direction to line up that mark with the pointer thats on the timing chain cover per mnf specs if I remember its 10 degrees when you get it there plug that "dummy " plug back in truck should idle up, if so tighten down the hold down bolt disconnect timing light and close the hood youre good to go at that point!

1993 Ford Ranger... | Answered on Dec 10, 2014

Seems that you have a power drain. If you installed any electronics check to see if the wire has an open section that is bleeding the system.
Check to make sure that when the glove box closes the light in side goes off. A sprung glove door will keep the light on and will drain a battery in about 3 days.
If you put a trailer hitch on the truck make sure that the grounding is done correctly. Lighting harness to trailer, trailer to truck. A poor ground will cause the electrical leak and drain the battery if the trailer in attached for a few day, less than 3.

1993 Ford Ranger... | Answered on Dec 10, 2014

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

621 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers


Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ranger Ford

  • Ranger Ford

Most Popular Question

truck check engine light when start bogs

  • Cars & Trucks