Need free pictures for a 1999 ford expedition fuse diagram
Posted by jdgjyfam on
If you go to the link below it will be the owners manual, it has all the fuse box diagrams in it.
Just select your model information and then click Submit, then click Owners manual from list. The fuse box diagrams start on page 131 of the owners manual.
Posted on Jan 17, 2011
Timing chain setup diagram shows the timing marks less than 90 deg from the cam cover surface. With the marks on my chain lining up with the timing marks, the sprocket on the passenger side of the car is greater than the 90 degs from the cam cover surface. This doesn't seem correct. Any assistance would be appreciated.
Posted by slugo301 on
Remove the two bolts, the timing chain tensioner and tensioner arm.
NOTE: LH shown; RH similar.
Remove the bolts and the timing chain guides.
CAUTION: Do not compress the ratchet assembly. This will damage the ratchet assembly.
Compress the tensioner plunger, using an edge of a vise.
If the copper links are not visible, mark two links on one end and one link on the other end, and use as timing marks.
If removed, install LH and RH crankshaft sprockets.
Position the tensioner arms and tensioners, and install the bolts.
Posted on Apr 07, 2010
Can you please provide me with a diagram/location of the low-side ac port on my vehicle to check for ac problems?
Posted by inlouisian... on
the low side charging port is near the AC Accumulator/Reciever dryer cannister in the larger of the 2 AC lines.
Posted on Apr 07, 2009
what is the tire size for a 99 ford xlt expedition
Posted by rennee... on
Your truck has 2 wheel sizes availiable 16" and 17"
here are the sizes for whatever wheel size u have.
Posted on Apr 16, 2009
Can anyone please tell me what size brake line and fittings I will need to replace rear brake lines?....
Posted by David... on
Which brake line are you talking about?. The metal steel ones,or the rubber ones. Doesn't matter. If you are buying the rubber ones, then just ask for them by year and model of truck.
If you are working with the steel ones, they are either going to be 5/16 or 1/4 depending which line it is. the 5/16 ones are usually attached to the master cylinder or the ABS unit. The fittings sometimes if you don't find the right one have to be re used, in which case you will need to flare the tubing. (Double Flare) Or you can go to the dealer, pay an arm and a leg, but you don't have to flare the tubing, which takes the fun out of the job.
Posted on Apr 07, 2009
where is the AC compressor relay on 1999 Ford Expedition
Posted by jessy9310 on
There's a A/c clutch relay if that's the one your looking for. that relay is located in the power distribution box located in the engine compartment (see picture below). The relay that I am talking about will be in the number 204 position (see picture of layout below). This should be in your owners manual if you have one. If you need an owners manual for your vehicle, email me at [email protected] with your make, model and year and i will be happy to email you one. Don't worry it won't cost you anything. I hope this helps you and good luck.
Posted on Mar 18, 2011
I have a Ford Expedition 2003 SUV and the heater stopped working on it. It works once in a while but now it seems to not work at all. What could be the problem and how could it be fixed. A/C works perfect but doesn't throw out any heat when I change the knob to red. Please help me!
Posted by aargueta29... on
This is all to common an issue in many Fords starting in the mid 90's, reason they went to a electric motor to control the air blend door , this motor moves the door air that diverts heat or cold from the AC, or mixes or blends it,the motor has failed or the door is stuck in the air duct, the bottom line is that to fix either problem the dash must be removed, no a job for the home mech, takes about 10-15 hrs to complete.
Posted on Dec 12, 2008
my low fuel light is on, but i there is a full tank of gas. the fuel hand also indicates low fuel. truck starts & runs fine...
Posted by russell... on
clean the ground to the body at the battery.
Posted on Feb 15, 2012
how do i bleed the brakes on a 99 ford expedition?
Posted by pruitt80 on
on the brake calipers ther is a bleeder screw. It looks like a grease fitting.1) fill brake fluid 2) have a helper pump the brake pedal ( vehicle not running ) 6 - 8 times to the floor and release then press pedal to the floor and hold with foot pressure pressing down. 3) at this time loosen the bleeder valve and the pressure and air will release,( do not allow brake pedal to release or come up, continue to hold to the floor ! ) after pressure and any noticeable air bubbles and no more fluid comes out then this is the time to tighten or (close ) the bleeder screw. 4) continue this process untill no visable air bubbles are present, IT IS VERY IMPORTANT THAT YOU CHECK THE BRAKE FLUID RESERVOIR AFTER TWO BLEEDINGS AND FILL AS NECESSARY ! 5) Continue the procedure on the opposite side. Do the two front wheels and the rear wheels as a pair as the brake system is a two part system, FRONT & REAR
Posted on Jan 17, 2011
removed spark plug wirers need firing order
Posted by trevinotaj on
Several engine sizes there...
1999 Ford Expedition 4.6 liter SOHC V-8 VIN "6"
1999 Ford Expedition 4.6 liter SOHC V-8 VIN "W"
1999 Ford Expedition 5.4 liter SOHC V-8 VIN "L"
Hope this help to solve it (remmeber comment and rated this).
Posted on Apr 20, 2010
2,747 questions posted
Usually answered in minutes!
Step 2: Please assign your manual to a product: