Top 20 2005 Ford F 250 Super Duty Questions & Answers

Just install cooling fan and wire to an aftermarket toggle switch. U can manually turn on/off cooling fan

If there re two wires?, hook them up and see if the fan moves in the right direction , if it’s not sucking air toward the engine?, swap them

lite blue with black trace . Free wiring diagrams here http://www.bbbind.com/free-tsb Enter vehicle info. year , make , model an engine size. Under system click on body & accessories ,then under subsystem click on power windows .

Could be FICM.....normally 48V...if voltage drops to low it will not start....I had one that was intermittent and then gave up ghost. Do you have a scangauge? Good tool to monitor engine parameters real time

no... will not reset by itself u will need a abs scan tool to reset it, so if u have a scan tool u can use it to tell u which brake disc abs wheel sensor needs to be CLEANED yes cleaned by letting it sit sensor disk rusted up... clean the rust off disc then use wd40 on it...

This engine is fully electronically controlled, so you need the dealer to do a full diagnostic of the engine control system, it is the only way to get to the bottom of this. Make sure you can show the dealer exactly what is going on otherwise if they can't duplicate the concern and no fault codes are present they can't fix it.

code reader reads powerbooster and control module ?????? What code's ? P1000 ? There are electronic's involved here you have no idea about . Unless you have a factory manual you never will and your best bet is to have it towed to a qualified repair shop .You don't need to know where the PCM / control module is . You will just make matters worst . Replacing a PCM requires programming , and a special tool that costs a few grand . So do your self a favor and take it to a qualified repair shop.

Yes it will, there are seals on the shaft, the pump forces fluid down the shaft into the torque converter, then it returns to the transmission.

There are a number of videos...For RWD front hubs. (F250 will just have larger bolts.)How To Install Replace Front Wheel Bearing Hub Assembly 2004-08 Ford F150For 4x4 front hubs.Ford Super Duty hub bearing replacement Driver side

Not to be a jerk, but you look in the manual. If you don't have one, you order one from any number of online suppliers who will sell you one. I did that for my 2003 Chevy Silverado pickup. If you're going to keep the car, you will eventually need it anyway. . .

I'd check to see if there is power to the fuel pump, if so, I'm guessing, bad fuel pump.

If you don't purge the power steering system correctly it could lead to premature power steering pump failure. You need to follow instructions correctly. You may need some special tools. I've never done this on your vehicle.

The only diagram the manufacturer provides is for the AC system. There is a basic engine diagram on the emissions label under the hood.

f-250 power stroke super duty 2005 starter relay? http://www.bing.com/images/search?q=f-250+power+stroke+super+duty+2005+starter+relay&FORM=HDRSC2 http://www.bing.com/images/search?q=f-250+power+stroke+super+duty+2005+starter+relay&FORM=HDRSC2

If the starter is new, and the battery is charged, then something is preventing the engine from turning over. Pull the glow-plugs, and turn it over. Does stuff shoot out of the holes? Head gasket blown... If it still doesn't turn over, seized engine is likely.

you need to bleed and prime the system. Diesel engines won't start if there is any air in the fuel system.

Here is a link to a utube video. It's for a 2006 but should still be helpful. https://www.google.com/url?sa=t&source=web&rct=j&ei=iaTNVO_lHZPGsQSyt4CwAg&url=http://www.youtube.com/watch%3Fv%3DWEcyTSr090w&ved=0CCsQtwIwBQ&usg=AFQjCNGIQScORKFNg_Qv0fbAISST8bKLlw&sig2=_sTTJB_a4vi2RMhpBVvSUw Bob

it should be on the sticker under the hood that states the 6.2L engine.