20 Most Recent 1997 Ford Aerostar Extended Questions & Answers

Question edited for clarity. Question moved to model category. The PCV (positive crankcase ventilation) Valve is shown in the bottom link. Also click the images tab. It is already answered on Fixya.

Where is the pcv valve in a 1997 ford aerostar van

Fixya https://www.fixya.com > ... > Ford > Aerostar May 12, 2015 - Its plugged into one of the valve covers has a 1/2 inch hose connected to it that goes to the intake manifold . Where does pcv valve go on 1997 ford 35o with 460 motor? May 27, 2012 Where is the Purge Flow Sensor on a 1997 Ford - Fixya Oct 7, 2009 SOLVED: 97 Aerostar p0170 p1443 p0340 - Fixya Nov 15, 2019 More results from www.fixya.com

HELP PLEASE 97 FORD AEROSTAR PVC VALVE

Ford-Trucks.com https://www.ford-trucks.com > forums > 1499617-hel... Jul 18, 2017 - I have been searching the internet for days without any luck just to try and locate my PVC VALVE so it will pass smog. Where is the PCV valve on a 1993 3.0L Aerostar? Aug 23, 2012 97 7.3 passenger side valve cover hole - Ford Truck Enthusiasts Dec 16, 2021 97 Aerostar Timing Chain - Page 4 - Ford Truck Enthusiasts Apr 30, 2017 Ordered rockauto tune up parts for 97 Aerostar: questions??? Nov 9, 2009 More results from www.ford-trucks.com Link https://www.google.com/search?q=1997+Ford+Aerostar+van.+Location+of+PCV+valve ..

if you means the module for spark is integrated whit the computer

feel sorry for you cause aerostar is junk. get the ac service so it is not causing such a load

This may have 2 sensors since it's a v6.

I hope you made sure you had adequate fluid in the transaxle before trying to drive it! Did you SEAT the axles into the inner hubs (past a spring clip ring), or did you just slide them in until they stopped moving? Did you TORQUE the outer nuts to spec? There IS a possibility, that if you REMOVE the outer nuts and STRIKE the end of each shaft with a hammer, you MIGHT be able to seat the axles correctly ... assuming you did not do that before reassembling all the outer stuff.

EVAP purge valve stuck closed maybe . Read more: http://www.engine-codes.com/p1443_ford.html P0133 Ford O2 Sensor Circuit Slow Response Bank 1 Sensor 1

Check for spark, check for fuel pressure. it is one of those most likely.

Not very far if the belt runs the water pump.

Hi, download owner's manual here:
https://www.fleet.ford.com/maintenance/owners_manuals/default.asp

then turn to page 203. Please let me know if you have any questions.

Probably Multi-Function Switch And/or Connector Bad.

check for drive belt condition and tension. Check that all pulleys spin freely and are not making the belt slip.

There is no way to display trouble codes without a scan tool of some kind. Being a 1996 it uses OBD II protocol which means you can find a generic scan tool that will retrieve codes at most parts stores. Generally they will scan the codes for you for free. Just be careful about taking the parts persons advice as far as what it will take to fix the problem. Many times a parts person will recommend replacing whatever part the code says but that is often not the correct fix. For instance a code P0171 indicates an oxygen sensor is reading lean so a lot of times people will replace an oxygen sensor for that but it's rarely caused by a bad sensor . Typically it's caused by a vacuum leak or a bad mass air flow sensor or sometimes a weak fuel pump. I guess what I'm getting at is make sure you fully diagnose the vehicle. Knowing the trouble code is just the beginning there can be several causes for any given code.