20 Most Recent 1999 Ford Ranger SuperCab Questions & Answers

To reset the anti-theft system, follow these steps:
1. You have a little red light on your dashboard-press it to disarm the alarm
2. Try turning the key and moving the shift from park to drive and back, then try starting it again
3. Disconnect the battery and let it breathe for 20 minutes and more, and reconnect it, that may do the trick
4. If all else fails, you may need to go down to the dealership to reprogram the key

1999 Ford Ranger... | Answered on May 21, 2020

There's a website that has all this information about all this and manuals everything totally free there are many actually but I personally like few . reliable-store
let me know if u need help

1999 Ford Ranger... | Answered on Mar 01, 2019

Your fan motor has either burned out or there is a short in the wiring. Check for voltage at the fan motor plug under the dashboard. If you have power there then the motor is bad, replace the motor and you should be good to go.

1999 Ford Ranger... | Answered on Sep 30, 2018

fix the clutch problem
if cable replace the cable
If hydraulic , bleed the air out or replace both the master cylinder and slave cylinder

1999 Ford Ranger... | Answered on Feb 13, 2018

sounds like the linkage from the ignition lock cylinder to the ignition switch is broken.

1999 Ford Ranger... | Answered on Dec 12, 2017

if it has a dash mounted 4x4 switch have it checked

1999 Ford Ranger... | Answered on Nov 07, 2017

Rock it back and forth with pressure in either direction on gear selector. Manual or auto can have a safety switch after 1991. If sensor fails to detect park or neutral, no start.

1999 Ford Ranger... | Answered on Oct 30, 2017

You have to turn and push at the same time it will seat in then. When it goes in once keep turning and pushing to make sure it is all the way back.

1999 Ford Ranger... | Answered on Jun 01, 2017

Sounds a lot like it's been under water.
I found unplugging things 1 at a time and reconnecting shaves the corrosion off. Check the Earth wire as well. Door sensor sounds like it's slightly out of alignment.

1999 Ford Ranger... | Answered on Apr 17, 2017

You may be hearing the pressure regulator that is relieving the pressure on the rail and returning it to the tank.

1999 Ford Ranger... | Answered on Mar 19, 2017

First thing to do is check the fuel pressure, it should be 42-46 PSI under a load. If that is ok then run a fault code test to see if any codes are in memory.

1999 Ford Ranger... | Answered on Feb 06, 2017

Any fault codes showing in memory when you read the codes.

1999 Ford Ranger... | Answered on Sep 30, 2016

Center of dash behind the controls.

1999 Ford Ranger... | Answered on Sep 13, 2016

1999 Ford Ranger Vacuum hose diagram
Pamela, Normally vacuum line routing can be found under the hood of truck, on Rad support or on the underside of hood. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
Ford Ranger Engine Vacuum Hose Diagrams
Vacuum Lines The Ranger Station Forums
Repair Guides Vacuum Diagrams Vacuum Diagrams AutoZone com

1999 Ford Ranger... | Answered on Jun 12, 2016

Not finding what you are looking for?
1999 Ford Ranger SuperCab Logo

1,025 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ranger Ford

  • Ranger Ford

Most Popular Question

1999 ford ranger 3 0 truck arc solenoid

  • Cars & Trucks