Top 20 1984 Ford LTD Questions & Answers


Not possible to diagnose over the Internet. Could just be low trans fluid or trans problem.

I’m happy to help further over the phone at https://www.6ya.com/expert/donald_f2ed37026a3ac881

1984 Ford LTD | 23 views | 1 helpful votes


9 foot pounds. In inch pounds would be 108 in/lbs.

1984 Ford LTD | 35 views | 0 helpful votes


Should be one... under steering column.456f6382-7d8d-49f5-ac4e-188dba685f60.gif

1984 Ford LTD | 229 views | 0 helpful votes


Fuse 16 should be a 20 amp fuse.

1984 Ford LTD | 71 views | 0 helpful votes


Check fuses...may be tied together on one fuse or have seperate fuses

1984 Ford LTD | 69 views | 0 helpful votes


When was the last tune up? There is a few things that come to mind. possible low fuel pressure, dirty fuel injector, throttle body could need cleaning, dirty fuel filter, water in the fuel, spark plugs need to be replaced or re gapped. I need more information to try to be more helpful.

1984 Ford LTD | 194 views | 0 helpful votes


I think you mean "idle".
If you have not already, remove the battery cables and clean the battery posts.
Let me know if it still does not crank.

1984 Ford LTD | 69 views | 0 helpful votes


You should be able to look that up on the auto parts stores' websites.
Just key in your year make model and engine size.
The stores usually have books that have the pictures too.

1984 Ford LTD | 169 views | 0 helpful votes


The fuse block is usually located under the drivers side dashboard...many require you remove the under dash panel to see it. You can go online to find an owners manual for your 84 LTD...if you plan on keeping this car, the manual is most helpful. Also the service manual should still be available through Ford, or online...you probably son't need the service manual unless you are exposed to many repairs. Hope this helps.

1984 Ford LTD | 591 views | 0 helpful votes


hammer and chisel is only way now ,try hammering an old socket over the locking wheel nut,also some motor factors sell a special kit for this job but they are only sold to the trade for obvious reasons so ask in a local tyre shop as they may have some

1984 Ford LTD | 122 views | 0 helpful votes


I had one do the same thing same year and everything ended up being the engine computer but first test the ignition module you can take it off and have it tested at most of your local parts stores it is located on the distributor and you will need a special tool to remove it which can also be purchased through your local parts store for a few bucks just tell them you need a ford ignition module and they should know right what you need good luck hope this helps

1984 Ford LTD | 130 views | 0 helpful votes


For a while in the early days of pollution control there used to be an air pump which forced air into the side of the catalytic converter in order to lower the percentage of bad stuff in the total output of the exhaust. Perhaps that is what you are looking at. Most were disconnected almost immediately but no later than the first replacement of the converter.

1984 Ford LTD | 161 views | 2 helpful votes


For 1984 Ford LTD 3.8 liter V-6 VIN "3" TBI check...

3f47c7c.gif

Hope this help (remember comment and rated this.)

1984 Ford LTD | 344 views | 0 helpful votes


Here's the diagram you asked for...


74d146c.jpg

1984 Ford LTD | 153 views | 1 helpful votes


5.0 fuel injected.774cbfa.gif

1984 Ford LTD | 133 views | 0 helpful votes


135624 with no 1 at the front of the car.hope that helps.

1984 Ford LTD | 116 views | 0 helpful votes


I likely have the pic you need. But first, what are you working on? You have a 84? 83? Crown? Did you put this motor in? What is it out of?

1984 Ford LTD | 86 views | 0 helpful votes


I'd be severely worried if you didn't have coolant in your engine!

I presume that you meant you are finding coolant in the oil or that there's lots of steam coming from the exhaust even after the engine has warmed up.

If so, then there is no temporary fix. Putting the job off will at best ruin the cylinder head and at worst completely wreck the engine, so basically the longer it's left, the higher the costs.

There is only one fix and it's a full head gasket replacement and top end overhaul. If you have been filling the cooling system with water only and there is no antifreeze/corrosion preventer in the coolant then the engine block may already be ruined, but I've rarely encountered that situation except when working on engines which have had years of abuse and poor servicing.

1984 Ford LTD | 202 views | 0 helpful votes


I would start by checking the oil, if the oil is milky on the dipstick it most likely has a blown head gasket. Then make sure the exhaust is normal. Does it smell bitter sweet or is it a white cloud? if it does it is a head gasket issue.

Heater not working could be thermostat or plugged heater core. I would place my money on the thermostat if the rest of it checks out.

Keep your head about you and you might be able to get this car cheap over a simple $8 part.

1984 Ford LTD | 57 views | 1 helpful votes


What do you need to adjust? What is the symptom?
If you need to adjust the idle, there is an idler screw that has a tension spring on it so it will stay in place. Tighten it clockwise to increase the idle RPM and counter-clockwise to lower the idleing RPM.
Treat the linkage arms with carburator cleaning spray (AutoZone $4).

1984 Ford LTD | 156 views | 0 helpful votes

Not finding what you are looking for?
Cars & Trucks Logo

Popular Tags

43 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

LTD Ford

  • LTD Ford

Most Popular Question

car set in grage 9 years

  • Cars & Trucks
Loading...