20 Most Recent 1989 Ford Crown Victoria - Page 6 Questions & Answers


Try cleaning the injectors... http://fordfuelinjection.com/?p=82 will give a few ideas on how to do a cleaning. Other than a cleaning, you need to be sure that the injectors are receiving the signal to operate, this is tested with a noid light.
Other than that, if you still want to replace the injectors, first relieve fuel system pressure by: 1) Look in the trunk for the fuel pump shut off switch. Turn it off.
2) start the car and let it run and stall out (should not take long)
3) Now the fuel system is depressurized
Now you can go in and begin the removal. 1) remove air intake plenum (on 5.0 it is the metal swept to one side looking thing on top of the engine)
2) remove the fuel rail assembly (you will need fuel line couple tools to make this happen, otherwise trying to improvise one will damage the coupling and give you a fuel leak)
3) Detach the electrical connectors from each injector (be careful and gentile like)
4) Grip the entire fuel injector with one hand and pull while gently rocking it back and forth. Don't yank, use a stern wiggle
5) First check once you get the injector out will be the O-rings, look for deterioration cracks or other signs of boo. (In general, replacing the O-rings is recommended once you have the injector removed)
6) Inspect the injector for signs of wear, and deterioration or breakage (if broken, you may want to investigate your manifold for the offending pieces)
Reinstall: 1) Lubricate the O-rings (use light oil only...no grease/silicone, they will clog the injector)
2) Lightly twist the injectors into place.
3) replace the previously removed parts
Tips: Recommend using a digital camera before and during your procedure. That way you have a photo reference of what things looked like before they were disassembled as well as what the progress was like, and you can refer to your own photo guide as you work.

1989 Ford Crown... | Answered on Nov 19, 2010


If you have more than 100,000 miles use high mileage oil. In the spring and summer use 10w30 and if it gets bellow -20 where you live use 5w30 in the winter

1989 Ford Crown... | Answered on Oct 20, 2010


well if it has power door locks yes the actiator could be bad that locks it if not you should get some pb blaster and pray back in there

1989 Ford Crown... | Answered on Oct 10, 2010


you unbolt the entire fuel rail from the intake manifold and pull it up gently. You can leave the rail connected to the fuel supply hose. You may need to remove the connectors as well to get it up high enough to change the o-rings. use a little oil or grease on the orings to slip them back in the same way you pulled it out. If you have more questions, let us know.

1989 Ford Crown... | Answered on Oct 02, 2010


loosen lug nuts. jack car up. Take wheel off. take the 2 bolts out of caliber. then remove the caliber from rotor and then remove the brake pads. push back piston with piston pushing tool. insert new brakes into caliber and return the caliber onto the rotor. put the 2 bolts back in and return wheel by tightining in a star order and you are now ready to roll

1989 Ford Crown... | Answered on Sep 29, 2010


this is caused by the system being low on Freon due to a leak, have the system lead tested and repair and recharge as necessary.

1989 Ford Crown... | Answered on Sep 23, 2010


There is a cable that hooks to the throttle mechanism on the fuel injection system, called a kick down cable. When you press down on the gas pedal it pulls the kick down cable and downshifts the transmission. I would start by checking this cable. Make sure that the cable is not broken.

1989 Ford Crown... | Answered on Sep 14, 2010


Fuel filters are typically located next to a frame rail. You can trace the fuel line forward, starting at the tank, and you should come to the fuel filter between the tank and engine.

1989 Ford Crown... | Answered on Aug 22, 2010


1989 Ford Crown Victoria 5.0 liter V-8 VIN "F"

2581dec.gif

Remember rated and comment this; good luck.

1989 Ford Crown... | Answered on Aug 19, 2010


if the low side tube is cold while the compressor is working the problem will be on air door module, or one piece of hose from intake manifold go to recirculation door is dis connected, but if he compressor is not working, there is only two reason, even the refrigerant pressure is too high or too low, if low a leak on your system, if too high overcharge or clogged expansion valve or the condenser, if refrigrant is i the right pressure and compressor is not working, check the supply on main switch, ambient temperature sensor, refrigrant pressure sensor and the high pressure sensor, if all ok,. replace compressor

1989 Ford Crown... | Answered on Aug 05, 2010


its a fuse, check the fuse panel

1989 Ford Crown... | Answered on Jul 12, 2010


You have two of them before the Y pipe.

1989 Ford Crown... | Answered on Jun 21, 2010


Usually it is located just ahead of the passenger side rear tire on the frame rail. You may need a special tool called a fuel line separator or it may just have clamps to undo. You'll have to get underneath to see which case it is. Good luck!

1989 Ford Crown... | Answered on Jun 16, 2010


there is a reason why we are not providing what u asked for , we are not a parts site, we have no way to reference any part numbers, we have no parts manuals for any car or truck, if u need parts do a used part search using the web site below, they have cross over manuals and can supply all the parts u need, this was a car produced in huge numbers and there are lots of these in salvage yards, the parts request form connects u to 100's of yards and then they will email you with prices and availability of the parts.

http://www.car-part.com/

1989 Ford Crown... | Answered on Jun 15, 2010


Go to the website http://www.hemmings.com/

This place in Vermont publishes the magazine for only older and antique cars

Parts can always be found especially weatherstripping

Alsoi check out companies that reproduce weatherstripping as well

Soft Seal is one that specializes in them

1989 Ford Crown... | Answered on Jun 15, 2010


passenger side, near the firewall.

1989 Ford Crown... | Answered on Jun 13, 2010


Yukon 2007, when underestimate the speed to 100 km And more speed in a voice Mphaji unsnaps the bottom of the car
What is the problem when

1989 Ford Crown... | Answered on Jun 13, 2010


remove the screws for the catch all box ot the bottom of door, remove the window switch and the two hex head screws that hold the door panel on under the switch. remove the screws under the arm rest and remove it. When that is done it just un snaps from door

1989 Ford Crown... | Answered on Jun 11, 2010

Not finding what you are looking for?
Cars & Trucks Logo

250 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Crown Victoria Ford

  • Crown Victoria Ford

Most Popular Question

1989 ford crown victoria fuse box

  • Cars & Trucks
Loading...