2000 3.3l nissan motor runs very rough, stalls, worse in reverse code PO325 knock sensor. What should I do? 160k miles
Posted by Duda1984 on
check wiring and connection if good replace knock sensor
Posted on Nov 16, 2009
engine repair code P0325 on a Nissan frontier v6 3.3
engine repair code P0440 on a Nissan frontier v63.3
Posted by steven... on
po325--ignition system or missfire.
Posted on Sep 16, 2009
how to check and add transmission fluid in a 2001 nissan frontier
Posted by schickhapp... on
Im guessing this is an automatic, theres a trany dipstick, engine should be at operating temp and the truck level remove the dip stick and wipe clean then reinsert and pull out the fluid should be in the hass maxs. if this truck is manual trans then the trany is checked from under the truck, remove the fill plug on the side of the trany and fill unttil oil runs out the fill hole. hope this helps.
Posted on Oct 18, 2010
where is the fuse for the dash lights! they just went out checked all fuses even under the hood! cant find a fuse for the dash lights
Posted by chicago... on
The dash lights run thru the headlight switch and there are 3 fuses for the lighting switch. All are 15amp according to the diagram.
It doesn't tell me where they are. That should have been in the owners manual.
Posted on Jul 11, 2012
Where is the thermostat located in a 2000 Nissan Frontier Crew Cab pick up? Is it at upper radiator hose at the engine end?
Posted by 1jose... on
You are correct the upper radiator hose leads to the thermstat housing. The thermostat housing should be retained by only 2 bolts.
Posted on Mar 01, 2010
What is the ECM location on 2000 nissan frontier 3.3L vg33e?
Posted by Brad Brad on
Where is the fuel pump relay at on 99 Nissan Frontier 3.3
Posted on Jul 04, 2019
what are the signs and symptoms of a fuel pump needing replaced. Other than the obvious that the car will not start 2000 Nissan frontier V6, 3.3L 4x4 crew cab
You don't hear it running when your turn the key on just before the crank position.
You have replaced the fuel filter and it was pretty much stopped up. (destroyed pump trying to pump through stopped up filter.)
Because it was going bad you couldn't drive fast because it wasn't pumping enough fuel.
Disconnect fuel line and see if fuel comes out when you turn the key on.
Posted on Dec 23, 2010
How do I access the socket to change brake light bulb on a 2000 Nissan Frontier
Posted by brodon on
The entire bed line will need to be removed. The long screws that hold the metal bracet where the bed extender attaches also hold the tail light assembly in place.
I pulled the bed liner up at a 45 degree angle and layed it on top of the cab. This revealed the screws. Take both screws out and lay to the side along with the metal bracket for the bed extender.
Now firmly grab the edges of the tail light assembly and pull...there are 2 hard rubber nipples that snap in to hold the assembly. You will feel like you might break it but you won't..just pull straight back hard. The assembly will "POP" out and then you can just twist the back of each bulb there are (3) and pull out..now you will see the bulbs..just pull the bad bulb straight out and push the new one into place. Now just reassemble. Total time will be 30-45 min. for this repair.
Posted on May 04, 2010
How many miles until the timing belt needs to be changed, on a 4cyl nissan frontier?
Some say 80000,but I would say 60000,
Posted on Nov 06, 2009
how to replace valve cover gaskets on a 2000 frontier v 6 truck
torque specs for the rocker cover (valve cover) screws:
9 - 26 inch lbs
step one- 9 in lbs step 2- 18 in lbs step 3- 26 in lbs
tightening order (see diagram below)
Posted on Dec 28, 2013
800 questions posted
Usually answered in minutes!
Step 2: Please assign your manual to a product: