20 Most Recent 1999 Ford Explorer Questions & Answers

0helpful
1answer

99 Ford explorer hatch won't stay closed

check latch operation --is catch open -- debris --tab out of adjustment
11/17/2021 2:44:07 AM • 1999 Ford... • Answered on Nov 17, 2021
0helpful
2answers

I have a 98 ford explorer and the heater fan works only sometimes. I will have it turned on with the fan on high and get nothing for days. I leave it on all the time and then all of a sudden it star

Do you know how to do automotive electrical circuit testing ? Because this how one would find the problem ! Looking at a wiring diagram to see what all is involved , Fan switch , resistor pack , high speed relay etc..... Do you own a DVOM - digital volt ohm meter ? Do you know how to use one ? Free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. Year , make , model and engine size. Under system click on HVAC ,then under subsystem HVAC controls will come up on thier own . Click the search button then the blue link .The first link ,first diagram is the one you want to look at . Blower Motor Problems Auto Repair Help
7/12/2021 2:52:27 PM • 1999 Ford... • Answered on Jul 12, 2021
0helpful
3answers

Possible ignition switch problem? 99 Explorer

key chime sounds if the little tab is grounded where the key contacts it. The theft light is supposed to blink when the system is armed to let you know it is armed. That's normal.

What do you mean by auto door locks won't unlock? The remote doesn't work? the door lock/unlock button on the door trim panel? Do they lock ok? Or, just unlock doesn't work?
-----------------------------------------------------------------------------------------------

NOTE: The generic electronic module/central timer module (GEM/CTM) is connected to the ISO link and is diagnosed through the data link connector (DLC) with New Generation STAR (NGS) Tester.
There are five warning chimes and lamps the GEM/CTM controls: headlamps operating without the ignition on (chime only), door ajar (chime and lamp), key-in-ignition (chime only), driver seat belt warning (chime and lamp), and message center.


Audible Warnings Warning Condition Lamp Duration Audible Duration Audible Output Safety Belt 60 Seconds 6 Seconds Chime, 60/Min. 740 Hz Key In Ignition — Continuous Chime, 120/Min. 740 Hz Headlamps On — Continuous Chime, 240/Min. 740 Hz Door Ajar Continuous 1 Second Single Tone, 1000 Hz Message Center (Tone Request) — 1 Second Single Tone, 1000 Hz
When the is turned to RUN or START from OFF or ACC, the chime will sound for six seconds or until the safety belt is buckled.
The will turn on for 60 seconds or until the driver safety belt is fastened. Both the chime and the lamp turn on at the same time.
If the safety belt is buckled before the ignition switch is turned to RUN or START, from OFF or ACC, neither the chime nor lamp will be activated.
Anytime the is changed to RUN from START while the safety belt warning indicator is activated, the safety belt warning indicator will remain activated until either the timing sequence has been executed or the safety belt is buckled.
When at least one door is ajar and the key is in the RUN position, the door ajar cluster lamp is activated and remains on until all doors are closed. A warning tone will sound once any time the key is in the ignition switch and any door is open.
The key-in-ignition warning will sound when the driver side is opened with the key in the and the in OFF or ACC. It will continue to sound until the key is removed, the is closed, or the is in RUN or START.
The headlamp-on reminder chime will be activated if the headlamps or parking lamps are on, the key is not in the ignition switch, and the driver door is opened.
A single tone will be provided each time a ground signal is received from the message center. A one-second tone will sound for warning indications from the message center. A 100 milli-second tone will sound for each message center button depressed.
------------------------------------------------------------------------
  1. NOTE: The generic electronic module (GEM)/central timer module (CTM) must be reconfigured upon replacement. Refer to the New Generation STAR (NGS) Tester help screen on the configuration card to program the Tire Size, Axle Ratio.
    The power windows system and rear window defroster system are (GEM) controlled systems.
----------------------------------------------------------------------------------------------
  • All Windows Operate With the Ignition in the OFF Position
  • Circuitry.
  • Accessory delay relay.
  • CHECK the accessory delay relay; REFER to Component Test. If OK, REPAIR circuit 400 (LB/BK). If not OK, REPLACE the accessory delay relay. TEST the system for normal operation.


-------------------------------------------------------------------------
report back
6/7/2021 7:57:00 AM • 1999 Ford... • Answered on Jun 07, 2021
0helpful
2answers

My 1999 ford explorer will not crank unless you short the starter

THE SOLENOID NEEDS REPLACED
4/21/2021 6:46:51 AM • 1999 Ford... • Answered on Apr 21, 2021
0helpful
1answer

What is the nut size on the rear hinges (roof

those nuts are 5/16ths.
2/25/2021 3:25:20 PM • 1999 Ford... • Answered on Feb 25, 2021
0helpful
2answers
0helpful
3answers

Where is the pcv valve located on a 1999 ford

What throws everybody is that the pcv valve does not insert into the valve cover as it does most cars. This one on the 1999 explorer is located directly behind or in back of the engine on the top of the manifold. You can spot this easier if you take off the covering(four screws) on manifold then you will see two hoses that connect to a plastic pcv valve (that's what threw me). this should help.
6/13/2020 6:39:51 PM • 1999 Ford... • Answered on Jun 13, 2020
0helpful
1answer

Remove radiator from 1999 ford Explorer

Condenser coil should unbolt from the radiator
3/7/2020 12:24:59 AM • 1999 Ford... • Answered on Mar 07, 2020
0helpful
2answers

Schematics for installing ignition switch for a 99 Ford explorer

If your wires somehow got disconnected or burnt go to a junk yard and cut out the connector with as much wire as you can get then match them up color to color or buy the chiltons book but it might not have that so the junkyard is the best solution
11/13/2019 5:39:58 PM • 1999 Ford... • Answered on Nov 13, 2019
0helpful
1answer

Rough idle

have you ever replaced the fuel pump relay?
2/27/2019 1:28:53 PM • 1999 Ford... • Answered on Feb 27, 2019
0helpful
1answer

My 1999 ford explorer 2x2 5.0 v8 drive does not work unless i give it gas. drives fine after it starts to go. Reverse works fine. fluid is good. Whats the problem? Help

Sounds like the diaphragm o ring that engages the forward clutch pack is worn, would recommend pulling out transmission and sending it to a specialist. It’s a very complicated job
12/25/2018 7:44:36 AM • 1999 Ford... • Answered on Dec 25, 2018
0helpful
4answers

How much oil do i put in a 1999 ford explorer when

1999 FORD TRUCKS EXPLORER 4.0L 6-cyl Engine Code [E] SOHC
Engine Oil Grade 1......API* All TEMPS......5W-30 Engine, with filter..........4.7 liters
1999 FORD TRUCKS EXPLORER 5.0L 8-cyl Engine Code [P]
Engine Oil Grade 1......API* All TEMPS......5W-30, 5W-20 approved for this application per Ford TSB 02-1-9 Engine, with filter..........4.7 liters
Here's the information your looking for and thank you for using Fixya





12/6/2018 2:57:01 PM • 1999 Ford... • Answered on Dec 06, 2018
0helpful
3answers

Diagram for fuse panel

this link you give you a PDF owners manual what you seek is fuse 9 and relay position #5 in the underhood power distribution box.

http://www.motorcraftservice.com/pubs/content/~WOXEXP/~MUS~LEN/42/99expog1e.pdf
9/11/2018 8:21:54 PM • 1999 Ford... • Answered on Sep 11, 2018
0helpful
2answers

1999 Ford Explorer fuse box layout

9/11/2018 3:59:56 PM • 1999 Ford... • Answered on Sep 11, 2018
0helpful
1answer

I would like to know what these codes mean

P0171 System Too Lean (Bank 1) P0174 System Too Lean (Bank 2) P0301 Cylinder #1 Misfire Detected P0302 Cylinder #2 Misfire Detected P0304 Cylinder #4 Misfire Detected P0306 Cylinder #6 Misfire Detected
7/1/2018 10:26:13 PM • 1999 Ford... • Answered on Jul 01, 2018
0helpful
1answer

Why does it sound like there is a trumpet in my engine when I stop at a stop sign or signal light?

This could be a leaking brake vacuum booster.
3/21/2018 12:45:30 AM • 1999 Ford... • Answered on Mar 21, 2018
0helpful
1answer

Why does my engine sound like a loud vacume cleaner, then want to stall out?

Year, model and engine would sure help
2/27/2018 11:58:52 AM • 1999 Ford... • Answered on Feb 27, 2018
0helpful
1answer
Not finding what you are looking for?

3,355 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1998 Ford Explorer
1998 Ford Explorer

2,991 Questions

1996 Ford Explorer
1996 Ford Explorer

2,303 Questions

2002 Ford Explorer
2002 Ford Explorer

2,304 Questions

2004 Ford Explorer
2004 Ford Explorer

1,506 Questions

2003 Ford Explorer
2003 Ford Explorer

1,364 Questions

Top Ford Experts

gerry bissi

Level 3 Expert

4390 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8991 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6963 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Explorer Ford

  • Explorer Ford

Most Popular Question

99 ford explorer hesitates when put in

  • Cars & Trucks
Loading...