1987 Dodge Ram Maxivan - Answered Questions & Fixed issues

Depends on the car.

1987 Dodge Ram... | Answered on May 03, 2013 | 19 views

Try connecting plastic tubing to drivers side bleeder valve. Place end of tube into a half full can of brake fluid. Press the brake repeatedly with the engine running so your power braking system is working. Watch the tubing until all bubbles have been pushed through the tubing. Repeat for the passenger side. The plastic tubing needs to be submerged in the fluid in the can to keep it from letting air back into the system through the bleeder valve.

1987 Dodge Ram... | Answered on Feb 08, 2011 | 289 views

Must likely your brake pads are worn out and the steel backing is in contact with the rotor. Better get it looked at quickly otherwise you will have to have the rotors ground or replaced as well as new pads.

1987 Dodge Ram... | Answered on Apr 08, 2010 | 105 views

One note- many thermostat elements can be installed backwards and while they will function, they don't allow full flow of the coolant like that.
Dunno what the bolt might be for-
Another possibility is a blown head gasket; if these fail between any combustion chamber and a coolant path, it will heat the devil out of coolant and generally cause exhaust fumes in bubbles in the cooling system. You can check for signs of rust on your plugs since the cooling engine will **** in coolant and that will leave deposits. Also check your coolant for any signs of a milkiness and your oil for signs it is turning into hand-lotion.

1987 Dodge Ram... | Answered on Apr 01, 2010 | 147 views

Go to freemanuals.com on the web. They may have yours

1987 Dodge Ram... | Answered on Mar 30, 2010 | 265 views

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

on the following LINK. It has the Belt Diagrams you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!
Again my apologies...

1987 Dodge Ram... | Answered on Mar 07, 2010 | 368 views

More than likely a restricted exhaust system (cat converter). Could be plugged air filter.

1987 Dodge Ram... | Answered on Dec 04, 2009 | 227 views

My personal opinion is you don't want to rebuild a caliper. Most times now calipers are replaced as a unit (you can replace just one side without a problem) as the labor and time to work on a caliper is offset by the price of a new or rebuilt unit from a parts store. I don't have the pricing for your particular vehicle, but a phone call to an auto parts store can get you a price and availability instantly. I'm not sure if most auto supply stores would even stock the pistons and seals needed for the rebuild job.

1987 Dodge Ram... | Answered on Nov 30, 2009 | 109 views

If its the piston thats sticking you can purchase a kit for it but your probably better off buying the caliper. If the caliper is sticking and not sliding back and forth you need to buy a brake hardware kit for it. From my experience the brake hose usally collapses on the inside and causes it to stick you might want to check this out.

1987 Dodge Ram... | Answered on Nov 30, 2009 | 1,285 views

sticking caliper pistons

1987 Dodge Ram... | Answered on Dec 01, 2009 | 83 views

Trace the secondary wire from the distributor cap to the coil pack.Using a test lamp see if you have voltage to the pack with the key on.if not,you may be correct if you do have voltage the coil is likely defective.Also check the cap and cable connection at the distributor cap

1987 Dodge Ram... | Answered on Nov 01, 2009 | 35 views

1. Check the Motors, or similar manual at your public library for your van or enter your problem in your internet search engine.

1987 Dodge Ram... | Answered on Oct 30, 2009 | 323 views

look under the chasis it should be there.most times it is on the drivers side near the middle.

1987 Dodge Ram... | Answered on Aug 13, 2009 | 330 views

yes it is in one of two places.The first is look under the hood find the blower motor on the left side standing infront of the van.look under the blower motor to the right and down it should be there.if not look near the center/rear engin compartment,to see if it is there.It is a white ceramic part about 2/3 inches long with twqo wires on it.

1987 Dodge Ram... | Answered on Jul 23, 2009 | 498 views

i hate to tell you but your tran is no goog. you will needto replace it. sorry to tell you this

1987 Dodge Ram... | Answered on May 31, 2009 | 207 views

Please check this link: https://www.google.com/search?bih=625&biw=1366&hl=en&ei=gky-X-KLC67Tz7sPt5KToAs&q=2012+dodge+durango+navigation+screen+blank&oq=2012.+Why+is+navigation+screen+black&gs_lcp=CgZwc3ktYWIQARgAMgsIABDJAxAWEAoQHlDW1xBY1tcQYJDxEGgAcAF4AIABe4gBe5IBAzAuMZgBAKABAqABAaoBB2d3cy13aXrAAQE&sclient=psy-ab

I hope this will help.

Dodge Ram Cars &... | Answered on Nov 25, 2020 | 14 views

Here are the specs you're looking for:
• Font axle to hub nut torque 185 ft-lbs
• Front hub bearing bolts 60 ft-lbs
• Caliper housing bolts 125 ft-lbs
• Caliper guide bolts 26 ft-lbs
• front spindle hub nut 97 ft-lbs
• lug nuts 100 ft-lbs.

Dodge Ram Cars &... | Answered on Jun 02, 2020 | 2,510 views

Not finding what you are looking for?
Cars & Trucks Logo

21 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1999 Dodge Ram
1999 Dodge Ram

1,787 Questions

1994 Dodge Ram
1994 Dodge Ram

197 Questions

2004 Dodge Ram
2004 Dodge Ram

173 Questions

1998 Dodge Ram
1998 Dodge Ram

142 Questions

Top Dodge Experts


Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14850 Answers


Level 3 Expert

4369 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides