20 Most Recent 1999 Dodge Ram 2500 4WD Questions & Answers

The easiest way to remove these crankshaft sensors is to pull the transmission out. They are in a very poor location and anyone with a moderate size hand has trouble pulling these out without pulling the transmission out. The vehicle will not run if this sensor is out, and i recommend replacing it even if it wasn't bad if you ever have to work on your transmission or ever have transmission work done. Knowing you have a Dodge, presuming it's an automatic, you will, and i repeat, will have to get transmission work done.

1999 Dodge Ram... | Answered on Aug 27, 2019

Coolant temp sensor!! ECT!!

1999 Dodge Ram... | Answered on May 06, 2019

just a o ring 25 cents

1999 Dodge Ram... | Answered on Jan 21, 2018

Possibly fusible link in the positive battery cable. However if the fusible link blew you wouldn't have any power at all. Check for codes in the abs system. Most likely shorted out a relay.

1999 Dodge Ram... | Answered on Dec 26, 2017

You just go to the link I attached I'm sure you will get the solution of your problem
1998 Dodge Caravan Service Repair Factory Manual INSTANT DOWNLOAD

1999 Dodge Ram... | Answered on Dec 08, 2017

The Cummins does not have glow plugs as mentioned above. It has intake heaters. I have a 99 also and it is a cold natured girl on a cold morning. You should have a block heater to plug in when it is below 40 F. The electric plug should be on the passenger side just inside grill on the hood. You can plug it in all night or a couple of hours before you are ready to go and it should help. Also, since your wait to start light is not working, the intake heaters may not be working. Check them out.

1999 Dodge Ram... | Answered on Nov 14, 2017

get a second opinion from an accredited diesel specialist repairer shop

1999 Dodge Ram... | Answered on Oct 24, 2017

check the filters on the injectors, and the regulator. they have a small filter on each injector and one of the regulator. you can prime with the regulator off but only by hand not motor as it will go like a fountain. check the filters are clean, and refit once the fuel is pasted the regulator it should start to fire up.

1999 Dodge Ram... | Answered on Jul 21, 2017

that is not normal
there is a problem in the drive shaft by sliding so fa into the diff the cv joint"U" joint is no longer directly in line with the kingpin and is binding up as the steering direction is varied
the center line of the joint has to remain directly inline with the turning point ( king pin, strut ) so that as the axle is turning and the steering is turned the joint is in the same plane
check why the axle is allowed to move in and out and you will have your problem solved

1999 Dodge Ram... | Answered on Mar 31, 2017

Apparently nothing newer will fit. The part number is 4761544ab. Searching on that number will show a lot of online retailers - most are showing 'Discontinued'. A few will sell you the part but prices range from $300 to over $400. You might want to check with a salvage yard. If they don't have one, they may find a yard that does and will ship it. But you will probably still have to pay a 'premium' price for one.

1999 Dodge Ram... | Answered on Mar 20, 2017

just download the repair manual from the reliable store .com

1999 Dodge Ram... | Answered on Jan 26, 2016

Here is the easiest way . take a 14mm socket and extentsion and place it on the bolts and place againt your axle tube and start your truck and turn your wheel against it instead of pounding you will use your powersteering like a press to get your hub out its quicker and less strenous than pounding on the bolts ive done this many times i even made a extentsion for it i use a 14mm 1/2 drive shallow socket and a extension thats about 4 inches long i know im posting late on this one but if it helps anyone out then great

1999 Dodge Ram... | Answered on Jan 24, 2016

Sounds like it was pulling before the brake job...if so the only thing you didn't replace was the rotors, I assume you turned them? and did you see hard spots on the rotor? discolored area that didn't cut the same......switch the rotors left to right and see if the problem moves or just replace them if they've been cut twice.

1999 Dodge Ram... | Answered on Mar 23, 2015

Not finding what you are looking for?
Cars & Trucks Logo

553 questions posted

Ask a Question

Usually answered in minutes!

Top Dodge Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Ram 2500 Dodge

  • Ram 2500 Dodge

Most Popular Question

1999 dodge ram 2500 need replace rear

  • Cars & Trucks