1987 Dodge Ram Wagon B250 - Page 2 - Answered Questions & Fixed issues

Sounds like the fuel pump is going out. Its inside the tank. But first see if the fuel pump is clooged. take it off and see if its plugged. Check fuel pressure if you can. should be 45-55 psi

Dodge Ram B250... | Answered on Sep 17, 2018 | 614 views

On this website you find fuse box diagram and description for Dodge 1500 (2006)

Dodge 1500 2006 fuse box diagram

Dodge Ram B250... | Answered on Jul 01, 2018 | 3,121 views

If you talking about obd connection on driver's side near hood release

Dodge Ram B250... | Answered on Apr 15, 2015 | 425 views

Most accessory drive belts have an idler pulley that tensions the belt. The idler pulley either has s 1/2 inch square drive hole or some other way to apply force to counteract the spring. Identify the idler pulley and push it in the direction to loosen the belt, then remove it.

Dodge Ram B250... | Answered on Mar 06, 2015 | 408 views

How are you testing the coil? Coils don't go bad as much as people claim. What year is your dodge?

Dodge Ram B250... | Answered on Nov 20, 2013 | 274 views

Fusible links are normally located in a second, smaller wire attached to the positive terminal of your battery.

Dodge Ram B250... | Answered on Sep 29, 2013 | 157 views

I have the same problem-has happened twice. look for the power lock relay under the dash-I think this is the culprit. I'm ordering one from Rockauto and will follow-up on this elusive problem.
Arthur [email protected]

Dodge Ram B250... | Answered on Sep 21, 2013 | 551 views

The module should be in the distributor.

Dodge Ram B250... | Answered on Feb 06, 2013 | 66 views

The diagrams you need are in the factory repair manuals, you can download them HERE for a small fee.

Dodge Ram B250... | Answered on Oct 09, 2012 | 52 views

The positive cable sounds like the problem as almost as though it is shorting to ground,

Dodge Ram B250... | Answered on Sep 17, 2012 | 113 views

Usually, they are connected to the positive battery cable, or the starter.

Dodge Ram B250... | Answered on Jun 29, 2012 | 329 views

check to make sure distributor electrical wires been reconnected to distributor.and check to make sure distributor is receiving 8 volts supply from the pcm.check see if orange wire going to distributor to pcm getting power. because spark plugs not firing could be pcm, coil itself bad or crankshaft sensor bad. i would code scan vechicle before buying new parts ignition.timing off if you did not have distributor in number 1 firing position before removing the timing chain.

Dodge Ram B250... | Answered on Oct 04, 2011 | 458 views

code 21 is for the oxygen sensor. This controls the mixture of the fuel going into the engine. the sensor may be bad or its connector may be dirty or faulty.

Check for proper engine ground and ground to chassis for dirty or loose connections.

Check these items if problem persists after O2 sensor repair.

fuel pressure regulator

Dodge Ram B250... | Answered on Aug 18, 2011 | 605 views

It could be a fuse or relay.. Find the location of them in your maual..

Dodge Ram B250... | Answered on Jun 24, 2011 | 379 views

Dodge had a problem with he distributor bushing wearing out allowing the distributor shaft to wobble.
I have replaced several distributors in dodges for that reason.
If you hold pressure on one side on cap and it runs fine and quits when you release distributor cap the distributor will need to be replaced.

Dodge Ram B250... | Answered on May 21, 2011 | 79 views

Hi, assuming your parking lights work, I would say you have a bad wire from the switch to the dimmer.

Dodge Ram B250... | Answered on Feb 02, 2014 | 221 views

the only switch that you need to remove is the signal switch and hazard button that are held with screws.the hazard button has a screw(in the button)that holds the button to the side of the switch and the signal switch is held by 3 screws that you should see looking down at the switch.the one screw you will have to turn the switch to either left or right signal to gain access to it.disconnect the switch connection under the dash so you can pull up the switch to gain more access to the system.you will have to remove the ignition switch,with the key in there should be a small hole in the housing that you push a small pick or pin or drill into to push up the lock tab to remove the ignition switch.then you can continue.

Dodge Ram B250... | Answered on Apr 14, 2011 | 372 views

go to his web sight and down load the diagram book and then look up your make and model.


Dodge Ram B250... | Answered on Apr 12, 2011 | 236 views

Not finding what you are looking for?
Cars & Trucks Logo

Popular Tags

49 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2000 Dodge Caravan
2000 Dodge Caravan

2,243 Questions

1999 Dodge Durango
1999 Dodge Durango

-935 Questions

1999 Dodge Ram
1999 Dodge Ram

1,750 Questions

2000 Dodge Durango
2000 Dodge Durango

1,576 Questions

2005 Dodge Caravan
2005 Dodge Caravan

1,472 Questions

Top Dodge Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides