1983 Dodge Pickup - Answered Questions & Fixed issues


Manual transmission........ Set the emergency brake, or block the wheels. Now, using a large screw driver and a flashlight, look down into the shifter cover. You will need to line up the shifter so that it looks like a left-to-right long rectangle (each gear has a slider that moves front-to-rear). Once you have done that, you cannot fail getting the shifter into the correct place. f8p89np7+h6qjow4n4losaaaaaelftksuqmcc

1983 Dodge... | Answered on Dec 29, 2017 | 51 views


you can get the manual from the given link this is a very safe and secure link and it provide only those manual which is exactly you need to solve the problem i had already used this link for my problem to be solved and it helps http://toolsnyou.com/

1983 Dodge... | Answered on Aug 25, 2017 | 132 views


Hope this helps.


0241dcc.gif

1983 Dodge... | Answered on Aug 08, 2016 | 13,082 views


Did you check primary voltage at the coil, I believe it is a pink wire. It goes hot, either key on or engine cranking. With some older vehicles, they used a resister block, during cranking, it bypasses the resister and the coil gets full battery voltage, with engine running it goes through resister trying to make it easier on the ignition system. I'ts been a long time since I worked on this model year. Did you check voltage and ground, anywhere? Replacing parts may not fix it, if problem with wiring circuit, somewhere?

1983 Dodge... | Answered on Mar 07, 2016 | 57 views


How did you check your fuel gauge? The "Universal" fuel sending unit could be a problem.

1983 Dodge... | Answered on Sep 28, 2014 | 132 views


For this you have to determine when the #1 cylinder is at TDC (Top Dead Center) - when it would be firing. Take the distributor cap off and look at the rotor - it would be pointing at the #1 spark plug wire on the distributor. The wires would be connected it order around the distributor cap starting at 1. The sequence is 1-8-4-3-6-5-7-2 in a clockwise fashion.

1983 Dodge... | Answered on Sep 27, 2014 | 570 views


http://www.upullandpay.com/Cross-Referencing.aspx

you need a cross reference for auto parts..
try this site, it may help..i just found it after a quick google search.

hope this helps, or puts u on the right track

1983 Dodge... | Answered on Aug 26, 2014 | 173 views


Is the rod going up to distributre removed.

1983 Dodge... | Answered on Aug 02, 2014 | 31 views


Jack it up and put solid brace under to hold up. Remove jack. Take tire off and you will see some push on holders on the lug screws. Remove them carefully as you will reinstall them. Then the drum should slide right off the lug screws.

1983 Dodge... | Answered on Jul 16, 2014 | 34 views


have u checked to see if you have fuel

1983 Dodge... | Answered on Mar 06, 2014 | 23 views


Vacuum diagram? - Turbo Dodge

www.turbododge.com > ... > Carburetted and TBI Injected . you should be able to find every thing you want to know here

1983 Dodge... | Answered on Apr 11, 2013 | 902 views


Click here Daniel to see repair guide.

1983 Dodge... | Answered on Feb 11, 2013 | 79 views


pretty easy, and you can do it with a helper the old school way.
The order you will bleed them is right rear, left rear, right front left front.
(you should bleed toe longest lines first.)

Open the hood and fill the master cylinder with DOT 3 brake fluid.

Close the cover to the master cylinder.

Get in position at the right rear wheel with the wrench ready to open the bleeder screw on the back of the wheel cylinder.

Have the helper push the brake pedal 3 full times to the floor and hold it down on the 3rd pump. (keep pushing it down)

They should say "Holding" at that point and you will open the bleed screw just a little until you see fluid coming out.
(the pedal will fall to the floor when you open the bleed)

You should close the bleed screw before they release the pedal.

Repeat the process a few times until you don't see air or dirty fluid.

You should check the fluid level every few times you repeat this to make sure it's still full of fluid, and make sure to seal the master cylinder cap before pumping the brake.

The process is the same for all 4 wheels.

You can also use a small clear tube/hose.... put it over the end of the bleed screw and the other end in a bottle or something to catch the mess coming out.

They sell one man bleed kits at the autoparts places, but I found them more messy and not as good as the old way.

hope this helps.

1983 Dodge... | Answered on Dec 24, 2012 | 80 views


Usually a sign the master cylinder has failed.

1983 Dodge... | Answered on Dec 24, 2012 | 17 views


Here's a link to the firing order.

1983 Dodge... | Answered on Nov 26, 2012 | 650 views


1-8-4-3-6-5-7-2

Distributor roatation is clockwise; odd cylinders are on left side of vehicle with #1 at left front.

1983 Dodge... | Answered on Oct 05, 2012 | 243 views


at the base of the steering colomn where the colomn goes under the dash is a panel that is held on with two screws take them out and the panel comes off

1983 Dodge... | Answered on Aug 25, 2012 | 84 views


I would try a salvage yard or craigslist

1983 Dodge... | Answered on Aug 22, 2012 | 36 views

Not finding what you are looking for?
Cars & Trucks Logo

192 questions posted

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14852 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...