20 Most Recent
1992 Chevrolet C2500 - Page 6 Questions & Answers
ASSOCIATED MODEL6018 FAST CHARGE 40/20/5
Are you asking about internal or external wiring?
To hook it up to a car, the black handle goes to frame ground (not the negative battery terminal) and the red goes to battery positive.
If you need internal wiring, please give me a complete description of what needs to be wired and why (ie - charger works but 200A booster for starting doesn't work, etc)
Engine quit running has fire
Hello and welcome to FixYa!
If you haven't considered replacing the PCM (powertrain control module) then now is the time. The PCM is the car's computer that when it's faulty something will surely fail. One good reason why the engine won't run at all even you have a good spark. Vehicle nowadays are powered by sensors and this sensors are being controlled by the PCM.
Hope this helps and thank you for using FixYa! Have a good one!
Would it be worth it
Im not sure exactly what your question is but it is worth it to replace the wheel bearings because there usely the first thing to fail in the system . Im not sure if you mean front or rear front will go sooner you will have to take some things apart but most of the time if you are having a problem and you hear bearing noise it will correct it just back the new ones with greese and do bolth eighter front or rear witch is giveing you the problem and you might as well do the brake pads or shoes and rotors if its the front because you will have to take it all a part anyway . And check the spec for tightening them its not a set torque and a lot of times you will need to tighten them up after 3 or 4 thousand miles as the gresse moves and heats up for a while on the fronts olny The old bearing you drive out with a large socket and use the old beaing to press the new one in and the races if required on tapered rolleds . New rotors will have new races but you will also need a new inner seal always
I have a 1998 Cheverolet
Whenever you turn the steering all the way against the stop the pressure in the system skyrockets. If fluid is coming out of a hose there must be a leak in it. You should avoid turning the steering wheel against the stop if at all possible.
Is there a way to
Your message came up a bit short on the description.
If you are asking about wheel bearings,please get back to me as I can help on a simple way to help if they are not good.
It sounds as if the
get under & watch have someone help you,, you may need to shim starter, shims at autoparts stores..
My truck takes so long
Hi and welcome to FixYa!
There's a big possibility that the MAF sensor is faulty. If the MAF is faulty you'll have vacuum irregularities. No wonder why the idle speeds up and it may drop too in any given time. I suggest that you have the MAF sensor replaced to resolve the issue.
Hope this helps and thank you for using FixYa! Have a good one!
Eversinse iv owned the truck
The speedometer sounds like it is broken. You could probably find a used one and the cable and gear at a wrecking yard.
The high beams work but
Check the fuses. If both low-beams went out at exact same time, it is probably the fuse (hopefully not a wiring short).
If they went out with a couple days or weeks of each other, it could just be the bulbs. They typically have very close lifespans and if they were installed at the same time, could burn out near the same time.
If the fuse is good, take the bulbs out. Look for a break in the filament.
Sometimes a fuse can break right at the base and you can't see it and sometimes a bulb can burn out without breaking the filament. If you can't see a break in either, start by replacing the fuse. (You can even take a same sized fuse out of a non-vital electronic (maybe radio, or power windows) and put it in the low beam spot.) If they work, there's the problem. Replace the missing fuse and your good. If not, then replace the bulbs.
Should the overdrive be on
Hello kking.
I would run with overdrive off with that.
You may be able to flip it on when going on a downgrade. That's what I do to save a little fuel and reduce engine RPM.
When in drive the link between the engine and the driveshaft is the same speed,so there is less heat being generated inside the transmission.
More heat is developed in overdrive.
The overdrive gear is not designed to pull loads in many transmissions as well.
Hope this answers your question.
Thank you for using FixYa.
KL
My 2009 Chevy pickup with
Doing it together or apart dont really matter. If you do charge it together you wont be able to see what battery is going out.
Now if you do one by one you should be able to find the bad one just from the charger.
Now if you just ran the systm down charge together...
My 1995 chevy silverado pick
these trucks are known for having bad circuit boards in the wiper motor, should be able to find one at the local parts store, the board is BAD NOT the motor. if you need more help get back to me. Thanks Ray
WHERE IS THE FUEL PUMP
It's in the underhod fuse relay pael near the battery. theirs a fuse also in the same box and the box lid is markered.
Where is the test
assume you are referring to a 1996 or newer vehicle. under dash to left of steering column usually will be a black rectangular connector, some have a plastic cap over it. if you can't find it send me year and model of vehicle.
Not finding what you are looking for?