1981 Chevrolet Corvette - Answered Questions & Fixed issues

Use a mighty vac, it's a hand held pump. Available at most parts stores

1981 Chevrolet... | Answered on Oct 27, 2019 | 49 views

Start with dirty fuse connection and then look for mouse wire damage

1981 Chevrolet... | Answered on Dec 30, 2017 | 161 views

on the exhoust pipeclose to engine

1981 Chevrolet... | Answered on Sep 13, 2017 | 38 views

Sounds like the delayed wipers are not working but the regular wipers are working. If this is true check the delayed wiper board in the wiper motor it is probably shorted out.

1981 Chevrolet... | Answered on May 19, 2017 | 116 views

Could be the module is fubar since you have B+ at the terminal. U can also install a hidden double pole switch that deactivates the fuel pump and ignition circuits. And if you want to be fancy you can do the same with a relay that opens those circuits automatically when ignition key is removed so you do not even have to throw a switch!

1981 Chevrolet... | Answered on Apr 08, 2017 | 191 views

get a flashlight and get on yur knees and go down under drivers side under dash left of clutch arm on wall. there is a fuse box there. the larger one is under the hood next to the shock tower and controls more interior. make sure everything is plugged in well

1981 Chevrolet... | Answered on Sep 17, 2016 | 33 views

wrongly machined flywheel, oil/grease on the clutch disc/flywheel surfaces or defective parts. take it back to the shop. if all were done right including the parts, clutch system should work like new.

1981 Chevrolet... | Answered on Mar 21, 2016 | 72 views

Hello You will need to get a new ignition because I believe that one of the inside tumblers have fell Causing the key to be stuck .

1981 Chevrolet... | Answered on Apr 24, 2015 | 62 views

brake system not purged properly, might have air inside or front brakes have leak

1981 Chevrolet... | Answered on Mar 14, 2015 | 270 views

sounds like you may have an over fueling problem. check for a leaking carb allowing fuel to run into the intake after shut down. have you checked to see if your missing spark when this happens. if not check if it could be a distributor component problem or coil.

1981 Chevrolet... | Answered on Mar 14, 2015 | 74 views

Sometimes a temp problem like that is the ignition coil.
Hope this helps.

1981 Chevrolet... | Answered on Mar 14, 2015 | 44 views

1981 Corvette has an electical tachometer that is driven by impulses from the distributor. First, check for blown fuses, next make sure the tach wire is plugged into the distributor. Next bypass silver tach filter or capacitor located by manifold to see if the tach moves at all. If these steps do not reveal a change in tach operation, then the most obvious next step is to remove the tachometer and get a new board for the tachometer. Unscrew and remove cluster lens and then unscrew tach bezel, and gently pull out the tach noting position of insulators. I believe these boards are available still at local autoparts locations. Replace board, note position of insulators and reinstall tach, bezel and lens. Old corvette are cool and are pretty easy to work on! Should be fixed, enjoy!

1981 Chevrolet... | Answered on Feb 15, 2015 | 325 views

If you add to much freon the air compress won't enage and your a/c want come on.

1981 Chevrolet... | Answered on Sep 22, 2014 | 150 views

lights must be connected to a circuit that does not run thru ignition switch.

1981 Chevrolet... | Answered on Sep 21, 2014 | 125 views

you have a ground problem at tank or at gage

1981 Chevrolet... | Answered on Sep 21, 2014 | 107 views

Fill master remove bleeder have somebody rapidly pump brake pedal while you hold your finger over the hole. within ten pumps (usually) fluid should come out.By holding your finger over the hole you will feel air pressure let that pass Then do your manual bleed.If still nothing check the rubber line sometime they get messed up inside and fluid will not go through

1981 Chevrolet... | Answered on Aug 23, 2014 | 179 views

Ignition switch,bad fusible links, coil,ignition module. I have replaced several switches for this problem. At the coil, when you turn the switch on, there should be power. There also should be power when trying to start the engine. If there is no power while cranking, replace the switch. The reason it hits a cylinder or two is that the power goes to the coil, just not enough to get the engine running..

1981 Chevrolet... | Answered on Aug 09, 2014 | 75 views

Not finding what you are looking for?
Cars & Trucks Logo

257 questions posted

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides