20 Most Recent 1989 Chevrolet Corvette Questions & Answers

Check your fuel pressure it should be 40-47 with the key and engine off and 30-44 with engine running.If its not within these specs then replace the fuel pump and filter.

1989 Chevrolet... | Answered on Apr 29, 2020

The starter is located on the passenger side where the engine mates with the transmission. It's held on by two bolts and there are wire harness that need to be disconnected and are live so you need to disconnect the battery ground first. Good luck and hope this helps. Keep me posted if you need instructions to removing the starter or you can log on to Auto Zone and register free of charge and you can get a print out on how to get the job done with common tools. Be safe friend. 

1989 Chevrolet... | Answered on Oct 18, 2019

check the vacume pipes for leaks and cracks.
82crossfire-h4hpx0jsheu3g5mx3tchb5rl-4-0.gif Im hoping this is the engine as there is a number of different engines codes. but any sensor like air intake sensor or map sensor will need cleaning if it has bee stud as the dust will settle and stick to them, then engine will not get right information, also check the timing as a belt stud in the same place for a long time can stretch and even mold to the engine a can cause timing to be out. any engine that has been stud for long time even 5 years is a long time to be stud, will need an oil change and filters, if the spark plug leads are hard or crispy they will need replacing they should be soft and be able to wiggle. Iv heard of seafoam being used on an engine not been run for 10 years and that seam to clean out all the hard build up in the engine, but there is others you can use, but you need one that will be able to be sucked into the engine by the intake. injectors can stick or be clocked with old fuel residue. idle controller will probably need cleaning out aswell, use carb cleaner, MAF/MAP sensor needs a made for cleaner MAF has its own cleaner and is only for the MAF would thing carb cleaner would be fine for the map sensor, spray it inside and shack out again do this a few times. just to make sure its clean and any muck is out.

1989 Chevrolet... | Answered on Jul 14, 2017

The dist. is a half tooth off location. Pull the dist. an reset timing. Be sure #1 cyl. is at the top and the rotor is pointing to #1 in the cap. or firing order.

1989 Chevrolet... | Answered on Mar 14, 2017

replace the coolant temp sensor, not the coolant temp sending unit

1989 Chevrolet... | Answered on Nov 05, 2016

Linkage inside door may have come unconnected. There are small clips that hold this stuff together.

1989 Chevrolet... | Answered on Mar 06, 2016

Check the hazard switch may be sticking

1989 Chevrolet... | Answered on Nov 14, 2015

Hi there I am a mechanical technician engineer I fix the things normal mechanic cant! I fix mechanical and electric problem no matter what it is the problem with it!!!I I am very good and bless in my work I am 5gen mechanical engineering technician never have a problem I can not fix check out the grounds and the map sin.it may be taken in air also I would check out the throttle body and the throttle sin

1989 Chevrolet... | Answered on Oct 25, 2015

Sounds like ignition control module (small plastic piece in bottom of distributor). When it gets warm it's shorting out. Easy fix, disconnect battery, pull cap & rotor - gin module is 2 screws in bottom of distributor and 4 wires - replace wires in exact order and coat bottom of middle with dielectric grease, replace rotor, cap & connect battery NEGATIVE CABLE LAST!

1989 Chevrolet... | Answered on Jun 09, 2015

Am I missing something or is everyone answering the wrong question?
If I am reading this right you are having problems in your instrument cluster in your dash not being lit up on one side, correct?
If so it is most likely a burnt out bulb or two.

1989 Chevrolet... | Answered on Mar 28, 2015

Yes. On the key you will see a chip. It is surrounded by black plastic that holds it to the key. Use an OHM meter and put the leads to each side of the resistor/chip/key. This gives the resistance. But i would unplug the ignition wire(under the dash) and put a resistor in it's place. A hundred dollar key, compared to 2 dollars.

1989 Chevrolet... | Answered on Mar 28, 2015

Bulbs. Remove the bezel (I'm sure it is screwed On, find them), remove the instrument panel(definitely screwed on), remove the plug. replace the bulbs.

1989 Chevrolet... | Answered on Mar 28, 2015

most likely fuel injectors are failing

1989 Chevrolet... | Answered on Feb 26, 2015

Most common issue is the switch activated by the brake pedal to take it out of cruse jumps out of position or out of adjustment. Also has a fuse.

1989 Chevrolet... | Answered on Nov 26, 2014

I changed a Ford transmission one time with a different tranny not made for that model and my speedometer was way out so I had to watch my speed on the hi way so not to get a ticket. I really can't answer your question.

1989 Chevrolet... | Answered on Nov 08, 2014

Disconnect battery from car, use wrench to remove hold down of link, remove link, install new link, tighten up hold down, reconnect battery.

1989 Chevrolet... | Answered on Oct 09, 2014

check for a problem battery. bad connections on the battery posts and terminals. have a load test done on the battery. Check the earth wires on the battery to engine .

1989 Chevrolet... | Answered on Sep 28, 2014

Not finding what you are looking for?
Cars & Trucks Logo

335 questions posted

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Corvette Chevrolet

  • Corvette Chevrolet

Most Popular Question

1989 corvette two right brake lights

  • Cars & Trucks