20 Most Recent 2000 Ford Contour Questions & Answers


Oil pressure sensor or switch has to be connected to the main oil gallery and it is generally most convenient screwed into the oil filter head or the gallery side of the cylinder block - you omitted to say whether your car has an oil pressure gauge?
If there is a gauge the light might be switched by the gauge itself or if the gauge is electronic and computer driven, the computer might be switching on the light.

It is worth checking the vehicle handbook or a wiring diagram to be certain what you have and how it works.
Some vehicles are no longer fitted with an oil pressure light and other vehicles have a light for the oil pressure and another for temperature and/or oil filter blockage.

Low oil pressure light on shouldn't be taken lightly and if a replacement switch/sender doesn't cure it, you should have an oil pressure test carried out asap.

2000 Ford... | Answered on Oct 11, 2019


It's under the right side rear door unscrew the clamp and use fuel line separators to get the front line off push in and pull out the line on the back there's a clip you push out

2000 Ford... | Answered on Feb 04, 2018


Your high side pressure is to high. The refrigerant needs to be operating at the right pressures in order for the air-con to function properly:

If the pressure is too low, there is risk of compressor damage in addition to lack of cooling
If the pressure is too high, the effectiveness of cooling diminishes at the very least
To avoid hitting issues related to this, modern air-conditioning circuits are equipped with a pressure switch/sensor. Its job is to protect the system from self-destruction by preventing the AC from running under the wrong conditions.

2000 Ford... | Answered on Jan 17, 2018


Does the gas cap have suction when you unscrew it? It could also be a vacuum leak somewhere.

2000 Ford... | Answered on Dec 21, 2017


It sounds like trans problem but a throttle position sensor would be the part that you are gingerly feathering to get results. This is a part attached to the side of the metal air horn and you can use a Websearch to see how to replace that part. Find out if the parts store would let you return that electrical part if it does not immediately fix your problem. It is a start and is a lower priced part if you did not need it,

Some of the electric shift problems can be from plug-ins that connect the wires to the transmission, or internal trans problems. Check trans fluid levels. If high mileage clean fluid and filter change in trans would possibly help.

There are some designs in electric controls that even a burned out light bulb in the dash can change the electric values that affect shifting in a 4 wheel drive.

2000 Ford... | Answered on Dec 09, 2017


Was draw test done with engine hot ?

2000 Ford... | Answered on Nov 20, 2017


Hey DonAld, these are not hard to replace..( I do not know which engine you have..it makes a difference!! ).. take a PICTURE of where the current TPS os positioned and located... the radial (adjustment) location IS critical!!..
here is a link to Autozone, ...O'Reilly's, and Advance Auto should have one too..

Ford Contour Throttle Position Sensor TPS

https://www.oreillyauto.com/shop/ignition---tune-up-16776/engine-sensors-17084/throttle-position-sensor-12043/2000/ford/contour?q=tps

Advance Auto Parts Down for Maintenance

2000 Ford... | Answered on Sep 15, 2017


That is a common issue with CNG..sorry...

2000 Ford... | Answered on Aug 01, 2017


Did you check to see if you wired it the same way you removed it? Make sure you are wiring it the exact same way as it was initially.

2000 Ford... | Answered on Jun 09, 2017


I would say you have some other problem .I really don't think you could get even two bad sensors . I could tell you better if i knew the codes . high and a low voltage codes are referring to a circuit problem usually . This sounds like a problem with a relay contacts stuck closed .Thier are two relays

2000 Ford... | Answered on May 05, 2017


How many miles are on the car. It sounds like it is going into limp home mode in the computer. If that is the problem you may have a catalytic converter that is plugged or nearly plugged. If the cat gets plugged if won't allow fuel to be pulled into the engine and causes it to stall. Have you ran a scanner on the car to check for trouble codes.

2000 Ford... | Answered on Apr 13, 2017


Your best bet , take an have a fuel pressue an flow test done . If you think it's fuel related . I'm sure you probably don't have the tool's to do these tests. We test , not guess as to what could be the problem . If clogged fuel filter it wouldn't get any fuel an it wouldn't start an run at all .

2000 Ford... | Answered on Mar 01, 2017

Not finding what you are looking for?
2000 Ford Contour Logo

587 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1998 Ford Contour
1998 Ford Contour

867 Questions

1999 Ford Contour
1999 Ford Contour

534 Questions

1996 Ford Contour
1996 Ford Contour

353 Questions

1995 Ford Contour
1995 Ford Contour

309 Questions

1997 Ford Contour
1997 Ford Contour

276 Questions

Top Ford Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Contour Ford

  • Contour Ford

Most Popular Question

location oil filter 2000 ford contour

  • Cars & Trucks
Loading...