which way does the thermostat go in
no directions and don't remember what it looked like when taken out
Posted by cheryl... on
This should help.
Posted on Nov 18, 2009
I noticed this high pitched whining noise a few weeks ago. The mini van runs good. But the noise is a concern. When accelerating the whining pitch gets higher. I will be grateful for any help. Thanks!!
Posted by Sue Sue on
This Noise Description sounds Indicative of the Sounds that come from the Serpentine Belt Or Related parts such as Belt Idler Pulley or Belt Tentioner witch also has a Pulley, but if Tensioner itself is Literally BROKE I've replaced a number like this it will cause a Whining noise . Best case scenario its just the Belt, and if any of the other Problems turn out to be the Culprit the Belt MUST be Replaced Anyhow as Damage is Being caused By the Very Whining you hear.
PLEASE Spend the Extras $ for the BEST BELT as this Drives your Water pump, Alternator, A/C Compressor, Power Steering Pump All Crucial to Control of, easy Steering ,All Electrical-Power Distribution, The COOLING of Engine << VERY CRITICAL Component
The Pulleys usually have a more Hum type Whining. So I would say at Best The BELT , And WORST Belt Tentioner is Broke
Posted on Jan 14, 2009
2002 dodge caravan
I found a couple pictures; I wasn't sure of your engine size or if you needed the rear heater aplication so I picked the most common ones & attached them.
Good luck; Hope this helps
Posted on Mar 18, 2009
My heater in my dodge caravan does not blow hot air. When my engine finnaly heats up, it blows only warm air. Its a 2006
First of all make sure your anti-freeze is at specification level's as well as make sure With the engine cold start the vehicle remove the radiator cap and make sure you see the flow of anti-freeze while keeping your hands as well as your clothing away from moving parts feel both hoses going into your heater core if the one on top of hot one on the bottom is cold then you have a Clogged heater core in which case you will need to flush the system . a simple garden hose will do the trick simply remove Both hoses to the heater core with the hose at the bottom line apply the garden hose until liquid comes out at the top of the other hose will probably see a lot of gunk. Also ensure that the vacuum line to the round ball under the hood is connected and not dry rotted.this will cause a vacuum leak to not allow the switch to fully engage from cold to hot. I hope this helps you.
Posted on Nov 07, 2009
Can you give me an explanation and maybe a picture of how to remove and install a starter on a 2002 Grand Caravan?
Posted by ahunt001 on
1) disconnect battery cables and push them out of the way
2) underneath the van unbolt (13mm) large cable assembly from starter
3) push red clip forward on small starter connection and push in on clip to remove (sometimes these clips are a pain to get to release)
4) still underneath the van locate and remove bottom starter bolt (15mm) - the bolt is on the transmission side of the engine near the front motor mount bracket, the large wire assembly in front of the transmission sometimes hides it)
5) now you can work up top of the engine - located a stud above where you removed the bottom starter bolt. It will have two wires attached to it. I think the bolt size is a 13mm. Remove the two wires.
6) This stud is really a long starter bolt. If follow the stud to the engine block you will discover it has a 15mm nut on it. You will need a deep 15mm socket and extension to get this bolt out. Mine was really tight! I ended up removing the battery tray and loosening the coolant tank to get enough leverage.
7) Now you can go underneath and pull the starter towards the passenger side. I had to move a few wires to the side and tilt it to snake it out.
8) Installation is just a reversal of removal.
Posted on Jul 22, 2009
I have similar problem. Tranny won't shift. Codes pulled P0700 P0725 (engine speed input circuit). Does this mean the Input turbine speed sensors is defective?
Have a problem with a 2002 Dodge Grand Caravan. Has a hard time getting into gear and this am, engine warning light came on and wouldn't shift out of 3rd gear. OBDII came up with P0700 Trans control sys malfunction, P0731 Gear 1 ratio incorrect, P0733, Gear 3 ratio incorrect and P0870 Trans fluid pressure/switch c circuit. Any help with fixing this problem?
Posted by GJPR on
replace the input speed sensor to transmission and the wiring pigtail all are available at your chrysler dealer take your vehicle registration in to the parts counter so they have your vin # to get the right part and it is the front of trans by fluid linres to radiator.
Posted on Mar 08, 2009
I have a 1998 dodge stratus 2.4 liter and have replaced the input and out put speed sensors. Engine light went off but now I have a p1698 code is on. Car is still in lymp mode and all of the transmission lights (P,R, D, 3,2) are on and the odomiter does not read. As I understand the probem is the TCM and PCM are not talking to each other. Do I have to reset the codes in the car? Is this a bad ground? Other? Thanks,
Posted by pdewey on
p1698 code no instrutment cluster
Posted on Aug 17, 2009
Can you tell me where the neutral safety switch is located on a 2002 dodge caravan? I would appreciate diagram if possible.
Posted by KMOs_Dad on
It is in side the trans on top of the valve body. Why do you think you need to replace it?
Posted on Mar 03, 2009
replaced output speed sensor - same problem and codes returned - fluid looks good
Posted by elliott817 on
1998 dodge caravan code P0700-Transmission Control System (Malfunction Indicator Lamp Request) How do I fix this?
Posted on Nov 17, 2010
diagram for serpentine belt routing dodge caravan 2002 3.3l
Posted by andino1976 on
Click on the following free direct Link. It has the Serpentine Belt Diagram for your 2002 Dodge Caravan 3.3L.
Let me know if this helped, or if you have additional information or questions. Feel Free to contact me at FixYa.Com!
Posted on Apr 01, 2010
1,483 questions posted
Usually answered in minutes!
Step 2: Please assign your manual to a product: