20 Most Recent 1988 Mazda B2200 Questions & Answers


Can f8 engine fit in a nissan vanette ad wel as the mazda bingo?

1988 Mazda B2200 | Answered on Dec 06, 2018


Check the fluid, check for leaks, if there is replace the cylinder or hose and bleed the lines of any air. There a two cylinders, the master cylinder(on the fire wall not far from the brake cylinder) and the slave cylinder(on the gearbox) i think this maybe your problem.

1988 Mazda B2200 | Answered on Jul 28, 2018


indicates valve timing or ignition timing out
check the firing order as it could be 180 degrees out

1988 Mazda B2200 | Answered on Feb 16, 2018


The compressor won't turn on when the AC is not ready to work. The system has to be usable before the compressor will work.

1988 Mazda B2200 | Answered on Dec 15, 2017


e94d3fc.png03cad01.png
hope this helps...please vote thanks

1988 Mazda B2200 | Answered on Nov 27, 2017


Check fuel pressure. If good, rebuild carb.

1988 Mazda B2200 | Answered on Nov 12, 2017


hydraulic clutch system
if the clutch master cylinder is full of brake fluid
master or slave is by passing

shift linkage out of adjustment
worn clutch or pressure plate damaged



26235114-o4qxaik4ragwwyoapewpjppp-5-0.jpg

26235114-o4qxaik4ragwwyoapewpjppp-5-1.jpg

1988 Mazda B2200 | Answered on Jul 10, 2016


before replacing the oil pump, try replacing the oil filter with one from mazda. there really is a difference in oil filters. if this doesnt cure the issue, youre going to need to replace the oil pump.

1988 Mazda B2200 | Answered on Jul 25, 2015


Pay the checkout charge at the dealer. Only on hills?

1988 Mazda B2200 | Answered on Jun 01, 2015


!st check and make sure the water is flowing in the radiator, then check
the timeing, Mazda will run hot if the timeing is rong.

1988 Mazda B2200 | Answered on May 09, 2015


need to adjust idle speed by turning air adjusting screw on throttle body idle should be 750 - 790 RPM. make sure spark plugs and wires okay. make sure distributor cap and rotor good.replace fuel filter do a little tune because if engine not fine tuned one bad cylinder will cause engine not to idle if you have fuel injection system clean fuel injectors by filling gas tank full add a can of seafoam to fuel tank see what happens.

1988 Mazda B2200 | Answered on Mar 02, 2015


Hi
  • 1st thing you want to do is position the steering wheel straight, easier when you put one back on. If it's never been removed before you might need the help of a puller
  • 2nd is to disable the horn. Easiest way to do that is by just removing the negative cable from your battery.
  • 3rd is to remove center wheel cover on the three spoke steering wheel you can just simply peel the cover off. On two spoke steering wheels (which is stock), you'll need to remove three or four screws on the back side of the steering wheel. Then pull on the front cover, unplug the horn wire from the connecter, and set the center section aside.
  • 4th is to loosen steering wheel retaining nut. With a 21mm or 13/16ths socket and maybe a breaker bar, you'll want to loosen the retaining nut that is holding the steering wheel on the column. Back it off until it is approximately flush with the end of the bolt. Leaving the nut on the end of the bolt will prevent steering wheel from hitting you in the face when and if you try to use your own strength to pull it off.
  • 5th is pull the steering wheel. Try and give a firm tug on the steering wheel while wiggling it right to left to pull it off the column.
As said above, if the steering wheel has never been removed before, it's probably going to require a gear puller or steering wheel puller. You can acquire one of these at your local auto parts store. Good luck



25427593-4x2s1z0jvbsslw0vb5pe0icv-3-0.jpg

1988 Mazda B2200 | Answered on Feb 17, 2015


Remove drivers knee panel then electrical plugs to steering column. Nest inside the engine bay remove the bolts from the universal joint. Last remove the two bolts holding the steering column to the dash frame.

1988 Mazda B2200 | Answered on Feb 14, 2015


I'd say the coil is shot. However when ot does happen make sure you still have 12volts going to the coil. This will help eliminate wiring issues.

1988 Mazda B2200 | Answered on Oct 25, 2014


i have the same problem it turns over and its back firing could it be timing

1988 Mazda B2200 | Answered on Oct 15, 2014

Not finding what you are looking for?
Cars & Trucks Logo

546 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

2004 Mazda 6
2004 Mazda 6

714 Questions

2000 Mazda MPV
2000 Mazda MPV

669 Questions

1999 Mazda 626
1999 Mazda 626

533 Questions

2001 Mazda Tribute
2001 Mazda Tribute

577 Questions

2002 Mazda Tribute
2002 Mazda Tribute

590 Questions

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

B2200 Mazda

  • B2200 Mazda

Most Popular Question

oil pump shaft ajusted 2 2 mazda 1987

  • Cars & Trucks
Loading...