20 Most Recent 2000 GMC Yukon Denali Questions & Answers


Have you confirmed that its not a security issue? Did it die suddenly or was it bogging out for a while? Have you scanned the engine?

2000 GMC Yukon... | Answered on Jun 02, 2019


Your car is 18 years old. It's likely history. Sell it as is for what you can get.

2000 GMC Yukon... | Answered on Jul 15, 2017


You push the seat all the way back you go under on your back.

2000 GMC Yukon... | Answered on Sep 30, 2016


To reset it disconnect the Negative (-) battery cable for at least five minutes. But I know that will not cure your problem.

2000 GMC Yukon... | Answered on May 25, 2016


You have upscale - luxury ?
It's separate from BCM .
Headlamp Control Module (Luxury)
Lower center of the IP, to the right of the right side steering column support bracket

2000 GMC Yukon... | Answered on Jan 17, 2016


Look under dash , on top of the brake pedal Arm .

2000 GMC Yukon... | Answered on Dec 24, 2015


Remove the battery hold down located on the front side of the battery. Remove the ground terminal. Remove the positive terminal. Lift battery out.

2000 GMC Yukon... | Answered on Feb 20, 2015


Is this a factory alarm or an aftermarket alarm?

2000 GMC Yukon... | Answered on Feb 02, 2015


They should go off in about 20 seconds, I guess you already tried that. Then it must be a stuck relay or shorted wire.

2000 GMC Yukon... | Answered on Jan 30, 2015


1. First, insert the ignition key and turn the ignition switch to the "On" position (Do not start the engine). Leave the switch on for 11 minutes. The security light may flash or be on steady during this 11 minute period. Make sure the light is no longer on or flashing before proceeding to #2 .
2. Turn the ignition switch off for 30 seconds.
3. Turn the ignition switch to the "On" position (as in step #1) for 11 minutes again.
4. Turn the ignition switch off for another 30 seconds.
5. Turn the ignition switch to the "On" position for 11 minutes a third time.
6. Turn the ignition switch off for 30 seconds one final time.
7. Turn the ignition switch to the "On" position one final time and wait 30 seconds.
8. Attempt to start the engine. If the engine starts and runs normally, the relearn is complete. If the engine does not start, Go to this link for info
http://vatspasslockpasskeysecurityhelp.yolasite.com/

2000 GMC Yukon... | Answered on Dec 10, 2014


The best way to get a quick answer to that is to look somewhere like the Kelley Blue Book, to see what engine options came as original equipment (it will ask which you have, in order to set a price, and in the process will list the available engines for that model). However, I would call a vendor that replaces engines, because they could both quote you a price AND tell you which other engines would/would not mate to your existing transmission, which is a very important factor to consider.

2000 GMC Yukon... | Answered on Jul 20, 2014


you have a aftermarket alarm system. you will have to take it to an alarm specialist. (it also could be a bad battery in your remote)

2000 GMC Yukon... | Answered on Jul 18, 2014


i think that is a factory setting if it is a factory alarm. I have a 2001 and my horn honks once when I set it and no noise when I turn it off.(you probably have a aftermarket alarm)

2000 GMC Yukon... | Answered on Jul 18, 2014

Not finding what you are looking for?
Cars & Trucks Logo

226 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top GMC Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Ryan Lutton
Ryan Lutton

Level 3 Expert

1266 Answers

john h

Level 3 Expert

23590 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Yukon Denali GMC

  • Yukon Denali GMC

Most Popular Question

2000 gmc yukon denali 5 7l no start new

  • Cars & Trucks
Loading...