1997 Mazda B-Series - Answered Questions & Fixed issues
Running lights stop working on my97 mazda b-4000
The light switch is at fault or else you have a wiring issue..Check all fuses because some vehicles have Seperate fuses for certain seperate lights?..The light switch Is designed to work both running lights and headlights...Turn the switch halfway on and the running lights come on ...Then turn it all the way on and all lights work...If all fuses are good it should be a faulty light switch...
2/6/2015 5:32:16 AM •
1997 Mazda...
•
Answered
on Feb 06, 2015
•
84 views
Tail lights go out when i press the brake pedal
It is the ground circuit that is the problem the bulb has 2 filaments and both are sodered to the bayonet which must ground the bulb check the mount screws that hold it to the lamp assembly they are loose.
4/23/2014 1:18:18 AM •
1997 Mazda...
•
Answered
on Apr 23, 2014
•
1,079 views
Mazda 97 WL 4x4 doesnt go over 80kms
Check that there is no air or air leaks in the fuel system. check that the fuel filter is clean. Check for correct bfuel cap on tank. Check that the accelerator pedal is not being prevented to going to the floor by a badly positioned floor mat. If you have a cable from the pedal to the fuel pump make sure that you are getting full throttle by having a frien push the pedal to the floor and checking if you can still move the pump lever further open. If you have and can adjust the cable length to take uo this slack
2/1/2013 11:04:17 AM •
1997 Mazda...
•
Answered
on Feb 01, 2013
•
105 views
Fuse blows when i turn
First make sure the fuse size it correct. there may be a small ampere fuse when it should be larger
Then test your compressor. you could unhook the wires from the compressor (mark where they go and put some black tape on them so you won't short anything out) and then turn it on again and see if the fuse blows again. if it does not blow then it means that the compressor is bad.
if it does blow you may have a ground on the wires somewhere.
hope this helps
rick
7/18/2011 1:40:05 PM •
1997 Mazda...
•
Answered
on Jul 18, 2011
•
141 views
Replaced clutch gearbox has noise
Did you replace the pilot bearing? It is the bearing that is in the flywheel, and holds the transmission shaft, and if it is not replaced then you will get the gear-box noise. I would recommend that you change out the gear oil as well.
4/13/2011 2:34:30 PM •
1997 Mazda...
•
Answered
on Apr 13, 2011
•
122 views
I cant find where the fuse for the alternator is
In the main connector to the battery positive are the fusable liks for the headlights and the altenastor you can find a bad one by pulling on them as if they come apart easily their bad. This is for the big wire on the back of the altenator. Theirs two wires in the plug one is hot all the tyime and the other is hot with the key on( this wire comes from the battery light) The gauges fuse powers them and if the temp gauge and the fuel gfauge work the fuse is likly good. If the altenator is
nt chatrging and all the wires at the altentaor are hot with the engine running ( not just the key on) then the altenator needs to be renuilt or replaced. Sometimes you can get it apart yourself and put brushes in it but most of the time this takes pratice and experience to do this correctly and the proper testing techniquies to get it right as the store sell rebuilt units for exchange. Always disconnect the battery to work on the altenatore wireing and when your problem is corrected right the battery fully charged up as the altenator is'nt a battery charger and can overheat and fail if it;s treated like one.
5/2/2011 7:16:18 PM •
1997 Mazda...
•
Answered
on May 02, 2011
•
358 views
Motor back fire when reving up timing on the marks
You have to really put some pressure on the timing belt tensioner,then tighten it down, make sure that belt is tight. then check your marks. You got them close because it runs, it's because on some models the belt has to be tight to get the marks to line up perfectly.
2/13/2011 2:48:37 PM •
1997 Mazda...
•
Answered
on Feb 13, 2011
•
137 views
Need a wiring diagram to hunt down why rear wiper
Mitchells, Motor, Chilton, Haynes, Clymer repair manuals all have wiring diagrams. If you cant obtain one of those your local library has a reference book section that should have a auto repair manual section.
11/19/2010 12:28:19 AM •
1997 Mazda...
•
Answered
on Nov 19, 2010
•
178 views
HOW DOES THE HEATER TEMP CONTROL WORK? I HAVE NO
its basicaly an electric switch that tells doors in your dash to let either hot or cold air in. if you havev no control over heat or cool air your going to have to replace the control unit. junkyard would be your best bet on a budget
2/20/2010 1:02:18 AM •
1997 Mazda...
•
Answered
on Feb 20, 2010
•
184 views
2002 ranger super cab. Why does alarm keep going off?
Hello. It seems your truck's key fob/remote either has a low battery and/or is 'wearing out'. The computer/alarm becomes 'confused' and can't decide if it should 'arm' or 'disarm'. This also causes slow to no operation of your vehicle's door locks. Good luck and keep me informed; if you want to.
1998 mazda b2500
In the low side line coming from condenser going in to either the accumulator or evaporator. There will be a union right where the tube is located
Not finding what you are looking for?