20 Most Recent 2000 Mazda Protege Questions & Answers

Is there a check engine light on? If so have it read to get the code. If you need further help, reach me via phone at https://www.6ya.com/expert/gary_9c859f4aa7e5ab10

2000 Mazda... • Answered on Mar 03, 2018

get a compression test done at a mechanic to check if you have a warped or cracked head. You may have a blown head gasket also ?

2000 Mazda... • Answered on Jan 15, 2018

As a canadian, those temps should not be low enough to drastically effect your clutch operation. Transmission fluid wont have any affect on the clutch mechanisms. Is there any difference in function once the vehicle has warmed up? i would check your clutch fluid for contamination. It will be a small resevoir on the driverside of the engine bay right under the windshield. It should look clear/maybe yellowish. Definitely not black or have anything floating in there, or if its low you could have some air i nthe system and in that case take it to a mechanic because there might be other issues. even though the clutch is slow to come back up that shouldn't effect the shifting with the clutch all the way down. Hard shifting can be cause by bad/low fluid but i would start with the clutch it might just be worn out.

2000 Mazda... • Answered on Dec 21, 2017

if you are in the usa, go to the advanced auto store, and let them, do it; @ no cost!. lol.

2000 Mazda... • Answered on Dec 20, 2017

the TPS is the throttle position sensor which has no relationship to a transmission problem run the fault codes and the TR , VSS and TCM are indicated problem areas

2000 Mazda... • Answered on Nov 22, 2017

too many variable including your workmanship best have the fault codes read and go from there

2000 Mazda... • Answered on Nov 08, 2017

Pressure test the fuel system to measure the pressure regulator to ensure correct fuel pressure under all driving conditions. Do the test with a less than 1/2 full tank of fuel.

2000 Mazda... • Answered on Oct 03, 2017

Check the pressure of the fuel pump if low pressure you need to replace

2000 Mazda... • Answered on Sep 30, 2017

Did you install a factory PCV valve ?

2000 Mazda... • Answered on Aug 15, 2017

Did it start doing this after installing the new battery?
Does it crank slow? If that's the symptom, I don't see how it could be many of the other things you listed. For example: a clogged fuel filter won't cause the starter to turn the motor slowly. Fuel filters rarely are the issue anyway.
If it's cranking fine but not starting when it's hot, start by checking electrical connections, primarily at sensors. Look for loose or corroded connections. Also, make sure the cables are clean and tight at the battery. I've seen some corrosion cause issues. Also check relays and fuses to be seated good and clean. Maybe wiggle them a little to make sure they are seated properly.
Unfortunately, electrical issues can be a pain to sort out.

2000 Mazda... • Answered on Jun 05, 2017

Look for a blown starter fuse or fusible link in your underhood block. Also look for what made it blow.

2000 Mazda... • Answered on Jun 03, 2017

abs (ABS)sensor is the anti-brake skid sensor and has nothing too do with the transmission you are referring to the vehicle speed sensor (VSS) run the fault codes as the TR sensor and the TCM are most likely the faulty sensors

2000 Mazda... • Answered on May 07, 2017

That is a question for the dealer if the info is not in your car manual.

2000 Mazda... • Answered on Jan 15, 2017

Not finding what you are looking for?
2000 Mazda Protege Logo

574 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top Mazda Experts

Thomas Perkins
Thomas Perkins

Level 3 Expert

14869 Answers

Greg Bernett
Greg Bernett

Level 3 Expert

2993 Answers

Brad Brown

Level 3 Expert

18664 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Protege Mazda

  • Protege Mazda

Most Popular Question

while driving car over drive light comes

  • Cars & Trucks