20 Most Recent 2005 GMC Yukon Xl Denali Questions & Answers

check the power plug array and see that the terminals are not corroded

2005 GMC Yukon... | Answered on Dec 08, 2018

Yes to much of this.

Compressor is close to the shocks - Start with electrics - Find wiring and check for voltage at the compressor - compressor is small like the little ones you buy for tire pumping - like small -

Jumper a temporary wire from battery to compressor does that work? If not just replace the compressor. I've replaced mine twice for corrosion issues.

If pump works, look for leaks or leaking shock. You can use a tire pump to check shocks leaking.

2005 GMC Yukon... | Answered on Feb 26, 2018

You can park on an incline with radiator cap off and heat on.

2005 GMC Yukon... | Answered on Feb 14, 2018

Define - It attempts to turn over but won't catch and run ???? When you turn the key to start does the starter engage an spin the engine ? This would be a crank no start condition . If the starter doesn't engage an spin the engine this would be a no crank no start condition . Sorry to ask but i have only been an auto tech for thirty years an have heard a lot of different discriptions for these simple actions . crank no start or no crank no start . Very different diagnostic procedures . So when you turn the key to start , does the starter engage an spin the engine ,but won't start an run ?

2005 GMC Yukon... | Answered on Jan 27, 2018

contact the dealership where you purchased the vehicle

2005 GMC Yukon... | Answered on Jan 20, 2018

Does the front blow cold ? Diagnosing rear problems
Taking to a qualified repair shop an having it diagnosed would be your best bet >

2005 GMC Yukon... | Answered on Dec 13, 2017

Your vehicle security system has malfunctioned, you need to have it taken to the dealer for testing with a special tool called a "TECH2 scanner. There may be a service bulletin on this problem and you may be able to get help from GM on the repair.

2005 GMC Yukon... | Answered on Apr 13, 2017

Most GM products have the o-tube located inside the evap metal line where the high side hose connects. Evacuate the freon, then disconnect the high side line. Look in the metal line coming out of the evaporator and there it is. These can require that you carefully screw a screw into the plastic part then use vise grips to remove. Usually, these are replaced along with the filter/dryer when recharging the system.

2005 GMC Yukon... | Answered on Jul 14, 2016

This sounds like a case of clogged oil galleys. These are the passageways that allow the top end of the engine to pass the oil back to the oil pan/crankcase. Though it's an unusual case, this is sometimes caused by excessive engine sludge, gasket media or other foreign deposits lodged in the galleys, etc. If you're able to let the engine sit long enough to try and allow the oil to drain back into the oil pan, remove the valve cover, and look in and around the oil galleys for any deposits or foreign material. They are generally located on the outer skirts of the head. The only time I've ever seen a case like this was from a valve cover gasket that was replaced while leaving the old one inside the rocker panel (head.) Of course, you'll most likely want to replace the valve cover gasket again after this test. Also check to make sure the PCV valve isn't completely clogged either, while you're at it. It's of course a simple, cheap, and much-needed part of a vehicle's maintenance.

Let me know if you need anything else in your diagnosis. I'm here to help! :)

2005 GMC Yukon... | Answered on Jun 28, 2016

Sound to me your valve guides are worn and letting oil get past the valves and being burnt in the engine,I hope this helps you and thanks for useing use at fixya

2005 GMC Yukon... | Answered on Jun 28, 2016

Mark, a lot of them do.

2005 GMC Yukon... | Answered on Feb 07, 2016

The Internet, though, has a large number of web sites where
you can buy service manuals and schematics from bookstores,
publishers, and other collectors. Here is just a sampling of
what sites are out there:

Factory Auto manuals
search for : factory service auto repair manuals

Repair Service Manuals
the largest collection of Automotive Repair Service Manuals
and Owners Guides on the internet. Our database currently
holds over 54,000 entries dating back from 1940 to more
recent 2011.

about Chilton Repair Manuals

about Haynes Repair Manuals
Haynes Publishing
Haynes auto manuals

2005 GMC Yukon... | Answered on Jan 18, 2016

Continuity meter.or a bulb on a wire one side to negative (any earth point) other wire to each side of fuse it should light both sides if ok

2005 GMC Yukon... | Answered on Oct 01, 2015

Yes you do have to take it to the dealer, This is a common problem in these trucks. This is caused by a bad encoder sensor in the shifter on the side of the transfer case. The sensor can be replaced with out having to replace the shifter assembly.

THe best test is to get the code from the system. This sensor is a sliding resistor and the material wears off causing a false reading. That is why the lights were showing Nothing, but you were able to drive. The code for the sensor is C0327.

TBS: #PIP3480M: Rattle Drone Or Buffeting Noise At Highway Speed In 2WD Or DTC C0327 - keywords 246 2hi 2high 4WD auto awd buffet buzz case click indicator knock lamp light service tick transfercase transfer vibrati - (Mar 4, 2008) Vehicles involved were built approximately between 01/01/04 and 03/06/06. The noise condition if not noticed by the customer may cause eventual encoder sensor wear causing DTC C0327 set in the Transfer Case Control Module (TCCM).

An updated TCCM calibration has been released to apply light pressure to the transfer case clutch pack and reduce the rattle. The calibration was released on 3/18/07 and the title line will read "to correct transfer case rattle at highway speeds and possible DTC C0327". For Rattle only (no current DTC C0327 set), Install the updated calibration and if necessary follow the diagnostics listed below

If the vehicle has a current or history dtc C0327 and can be diagnosed to the encoder sensor, re-flash with the updated calibrations and replace the encoder sensor as necessary.
Important Note: All NV246 transfer cases built 02/25/06 and beyond are manufactured with pressed fit parts to help reduce the rattle. Inspect the ID tag on the transfer case for this build date and verify the tccm has the latest calibration before repairs are initiated.

Thank you fur using Fixya and good luck.

2005 GMC Yukon... | Answered on Sep 23, 2015

Change Your Oil And Filter Then Remove The Negative Battery Cable To Reset It.

2005 GMC Yukon... | Answered on Aug 06, 2015

Not finding what you are looking for?
Cars & Trucks Logo

548 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

Top GMC Experts


Level 3 Expert

85239 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Ryan Lutton
Ryan Lutton

Level 3 Expert

1255 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Yukon XL GMC

  • Yukon XL GMC

Most Popular Question

tes square fuses in underhood fusebox

  • Cars & Trucks