20 Most Recent 1990 GMC Sierra Questions & Answers

set it at 12 degrees btdc where it should be If it has electronic timing it will advance /retard from that point and not as you expect to go to the correct setting

1990 GMC Sierra • Answered on Mar 07, 2018

Check the compression on each cylinder. Also check for proper valve operation. You may have a flat cam lobe or bad rocker arm on either the intake or exhaust side which will give the rough idle you are experiencing.

1990 GMC Sierra • Answered on Jan 03, 2018

Did you change the fuel presure regulator located in the throttle body?

1990 GMC Sierra • Answered on Nov 20, 2017

Pull the vacuum line of the transmission modulator valve. If there's oil in the line, the diaphragm in the modulator valve is cracked and engine vacuum is pulling trans fluid into the engine intakee

1990 GMC Sierra • Answered on Oct 18, 2017

Check the fuel pump relay first. It could be sticking. Under the hood fuse box. Little square switch module. Usually labeled on the lid of the fuse box. To test it,
Swap it with the horn relay if it's the same kind. (Usually is on gm/chevy) start it a few time to see if that changes anything. If not then it could be fuel pump itself

1990 GMC Sierra • Answered on Oct 17, 2017

old carb type do suffer from flowt problems, also people dont change the filters regularly so the inline carb filter blocks up., you would need to remove the carb and take the float chamber housing off. check the condition of the floats, and check the valve, if there is what looks like wet/dry dust in the float chamber then the filter has failed and you will need to clean the jets, you will need a few cans of carb cleaner or a big can of spray to clean it out. change the filters depending on carb fitted, there can be a filter above the valve or the fuel in line to the carb, also the main filter. replace the seals and refit when clean, would also at some point remove the tank and clean it out.

1990 GMC Sierra • Answered on Jul 14, 2017

i would check the the oil pressure sensor is not foul up this can happen sometimes, as there is vain in the sensor. this reads the pressure. and tell the ecu. and your display.

1990 GMC Sierra • Answered on Jul 02, 2017

Can you take pictures and add them in here ?

1990 GMC Sierra • Answered on Jun 25, 2017

The belt should not come off. If it didn't come off before the new alternator was fitted it should not came off now and the fact it does should not be your worry but the worry of the person who specified the repair, supplied the parts and carried out the repair. You presumably paid somebody to cure a problem and not to provide you with a whole new problem. Clearly the new tensioer has not cured the problem... If the pulleys are undamaged, perfectly round and the alignment is correct and the belt is tight enough, it should not come off. If the pulleys are ok and the belt is coming off then the belt isn't tight enough. I assume the tensioner is a spring loaded automatic type? If it is a spring loaded type, it indicates something sometimes is needing so much power to keep it turning it is overcoming the tensioner spring pressure and creating a slack belt. Sorry but other than that mad idea I have nothing to offer...

1990 GMC Sierra • Answered on Mar 19, 2017

Sounds to me you have high resistance problem , Main power feed to the alternator . Check the power junction block behind the brake booster on the fire wall . There is nothing in the instrument cluster to regulate voltage .B+ voltage to battery symbol when key is on , then when it starts voltage from voltage regulator inside alternator goes back on that circuit shutting off the light . Voltage on both sides of the light cancel's each other out . Yes, i would look for a burnt connector . at the junction block . Do a voltage drop test while the vehicle is running . Voltage Drop Testing the Charging System

1990 GMC Sierra • Answered on Mar 06, 2017

Visit the on-line store, know as reliable-store, they have the repair manuals. I'm sure you will get the solution of your problem. Best Manuals

1990 GMC Sierra • Answered on Dec 05, 2016

The flasher for the signals and the flasher for the hazards should be mounted on the left side of the dash slightly below the headlight switch. They will be most likely round and made of plastic or glass. Turn on the 4 way flashers and follow the noise. The signal flasher will be close to the 4 way flasher and look similar

1990 GMC Sierra • Answered on Nov 21, 2015

check to see if there are any codes. then check the EGR system for not closing completely causing a vacuum leak.

1990 GMC Sierra • Answered on Jul 20, 2015

Sounds like it may be?Is it about a .75" - 1.0" Hose?Because that is the normal size of heater core hose.

1990 GMC Sierra • Answered on May 08, 2015

Not finding what you are looking for?
Cars & Trucks Logo

398 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1998 GMC Sierra
1998 GMC Sierra

987 Questions

1997 GMC Sierra
1997 GMC Sierra

846 Questions

2000 GMC Sierra
2000 GMC Sierra

676 Questions

1999 GMC Sierra
1999 GMC Sierra

601 Questions

1994 GMC Sierra
1994 GMC Sierra

604 Questions

Top GMC Experts

Ryan Lutton
Ryan Lutton

Level 3 Expert

1266 Answers

john h

Level 3 Expert

23899 Answers


Level 3 Expert

4376 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Sierra GMC

  • Sierra GMC

Most Popular Question

solutions no fuel start up 1990 gmc

  • Cars & Trucks