20 Most Recent 1993 Mazda MX-6 Questions & Answers


IT IS LOCATED AT--BEHIND LEFT SIDE OF DASH IN RELAY BOX. (TURN SIGNAL AND HAZART FLASHER UNIT ) SAME FOR BOTH. PUT YOUR TURN SIGNAL ON AND TOUCH THE RELAYS IN THAT AREA YOUR ARE GOING TO FEEL WICH ONE IS WORKING, (DEFECTIVE FLASHER OR HAZARD SWITCH. )

1993 Mazda MX-6 | Answered on Oct 13, 2017


Ben, it could be something as simple as a bad tail light bulb or socket shorting out. Check all tail light bulbs, sockets and wiring for damage burnt etc.
Does it blow immediately, or when you turn lights on, or when you use left or right signal, or when brake is applied? this can help trace problem.

1993 Mazda MX-6 | Answered on Feb 09, 2016


When my MX6 was doing this it turned out to be an hydraulic leak from the clutch master cylinder, which runs on the same fluid reservoir as the brakes. Clutch master cylinder replaced and all good again!

1993 Mazda MX-6 | Answered on Jun 27, 2014


When working properly the hold button when pressed will hold the transmission from shifting gears until each gear is at the very top of the range. It is similiar to sport mode in other vehicles. It will allow for faster speeds during acceleration, but uses more fuel.

1993 Mazda MX-6 | Answered on Jun 25, 2014


radiator needs cleaning

1993 Mazda MX-6 | Answered on Apr 07, 2014


Are your headlights beams too high? too low? Then bear with me and maybe I can help
Horizontal headlight adjustment is easy. See the screw on the inside top of each light? turn the screw left and your headlight beam goes outward; turn the screw right and the beam goes inward, (toward the center.)
Okay now Vertical adjustment is a little more involved. Start by removing the corner lens; take out the screw on top of the headlight and pull the corner lens forward. This will allow you to access two 10mm bolts holding the headlights in on the sides.
Remove those, along with one 10mm nut on the backside of the headlight assembly (near where your bulbs plug in). Remove your headlight bulbs carefully - I usually put a paper towel around them to protect them from dirt and oil. Now the only thing holding your light housings on are the horizontal adjustment
screws. Just slide the screws out from the lens, and then remove the headlight from the car.
If you look at your headlights now, there is another screw that looks just like the horizontal adjustment screw.
In order to adjust this, you need to remove the 10mm bolt labeled "A".
Now slide the plastic headlight base off of that bolt. The whole plastic base will now be free to swivel on the adjustment screw. What you need to do now is to turn the plastic base around the screw; if you turn it clockwise or right, it will lower your headlight beam when reinstalled. If you turn it left, it will raise the beams.
I ended up only turning each side lower by one revolution. You shouldn't need more than one or two turns. It also becomes hard to slide the housing back over the "A" bolt after two turns. If
in doubt about whether the beams will be raised or lowered, on the final pic you can see the clean area of the bolt on the left side. if you lengthen this side, it causes the beam to go down.
Its really easier to understand as you are doing it, if this does not seem clear. Just use some common sense and you'll see what I mean.
Installation is the reverse of removal.

1993 Mazda MX-6 | Answered on Mar 15, 2014


You could try this page: http://www.partsgeek.com/ymm/1993/mazda/mx6.html?sort=pop&scat=engine_electrical

Without knowing the name of the part you could look at the different connector and match one up. Good luck!

1993 Mazda MX-6 | Answered on Mar 15, 2014


Coil resistance is not a good way to determine if the coil is good or bad. It might still need replacing. Check to see if your getting a pulse signal to the coil. You can do this by hooking a milivolt test light to the trigger wire and ground. If it doesn't flash as you crank the motor, check out your pickup coil in the distributor. Some of them you can change. Some you have to replace the entire distributor. Sometimes oil will leak into the distributors on certain models which use an optical pickup. If this is the case, change the seal to fix the oil leak and GENTLY clean the optical sensor and photo wheel.

1993 Mazda MX-6 | Answered on Oct 22, 2013


I found this lying around :-)
Hi people,
Im going to hopefuly help alot of people out, but at the same time will upset Mazda dealers.

I have the code to unlock Mazda radios the have 'ERR' due to 3 wrong codes. Do not listen to mazda book that states 3 wrong codes make CD playing Inop req replacement...

121 Metro DW10*2 > 203028, MX5 NB30P2,
Milennia, 323 BJ10*2, 626 GF10S2, and Tribute.
Step one: - press one at a time- preset 6, AM, Auto M, Seek ^ (up).
Step Two:-Input this number, 4989.
Step Three: - Press and hold Auto M and Preset 6 together.
Step Four: - The Word 'GOOD' will appear on the screen indicated that the radio will work.
Step Five: - Reprogram new Antitheft code into radio as per instruction manual.
Hope this helps some people out, save you some money as so

1993 Mazda MX-6 | Answered on Oct 18, 2013


Check your dissy, you could be out timing... if good, perform fuel pressure test...

1993 Mazda MX-6 | Answered on Jul 25, 2013


well try taking out the dash and see if it connected to the dash maybe it got pulled off when the tranny was out?

1993 Mazda MX-6 | Answered on Jul 01, 2013


Just try some patience. Smoke a cigarette and plan your attack but don't get angry.

1993 Mazda MX-6 | Answered on Apr 13, 2013


you will laugh at what this problem is i had the same problem i was ripping my hair out for weeks over it haha.... on your lower fog lights and the black bracket there attached to there is a connection that is for the lights. get it an slide it on to the the bracket it just slides on the bracket nice its actually an earth for it.... now take the negitive off the battery an place foot on break for 30seconds this resets the ecu oh remember to put it in neutral or in park when you do this with the left front door open an walaah prob solved

1993 Mazda MX-6 | Answered on Mar 23, 2013


in my opinion, the fuel oil is not enough.
_____________
mpps v13.02 download

1993 Mazda MX-6 | Answered on Mar 11, 2013


Sounds like your ignition coil is failing. Eventually it wont start at all Common problem

1993 Mazda MX-6 | Answered on Feb 13, 2013

Not finding what you are looking for?
1993 Mazda MX-6 Logo

174 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1994 Mazda MX-6
1994 Mazda MX-6

85 Questions

1995 Mazda MX-6
1995 Mazda MX-6

77 Questions

1996 Mazda MX-6
1996 Mazda MX-6

58 Questions

1990 Mazda MX-6
1990 Mazda MX-6

-15 Questions

1991 Mazda MX-6
1991 Mazda MX-6

-14 Questions

Top Mazda Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8984 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

MX-6 Mazda

  • MX-6 Mazda

Most Popular Question

fuse dash tail lights blow when turn

  • Cars & Trucks
Loading...