1994 GMC Yukon - Answered Questions & Fixed issues
94 Yukon cranks but won't start on cold mornings.
I hope I can help you with your question I believe I can first and foremost if you're having trouble starting your car on cold mornings it's probably going to be a clogged fuel filter or bad fuel pump about to go out you're having symptoms as you described and then whenever you're at 55° things start to warm up and you can start your car okay the filter is so clogged up imagine that look looking like a blood vessel okay when you have a clog in it it doesn't allow the blood to flow freely feel the same way
2/7/2018 1:53:55 AM •
1994 GMC Yukon
•
Answered
on Feb 07, 2018
•
250 views
Yukon wants to stall
Check the MAP sensor connection/connector and either the seal where it plugs in the intake or vacuum hose connection .
8/19/2017 10:01:47 AM •
1994 GMC Yukon
•
Answered
on Aug 19, 2017
•
61 views
Timing
Put a timing light on it and see if the timing jumps arround if so you chain could be bad. You should also put a fuel pressure gauge on it and see what you have for pressure,
11/10/2013 4:10:44 PM •
1994 GMC Yukon
•
Answered
on Nov 10, 2013
•
60 views
Starter
Either it will just click when you turn the key or a fast spinning sound of it turning the gear but it does not engage the flywheel.
5/15/2012 3:49:22 AM •
1994 GMC Yukon
•
Answered
on May 15, 2012
•
87 views
1994 GMC Yukon heat
This could be 1 of 2 things 1 being the heater control valve and the other is the heater core is clogged up.
1/21/2012 12:11:42 PM •
1994 GMC Yukon
•
Answered
on Jan 21, 2012
•
446 views
1994 Yukon Ive changed
Hi, the pump should be getting battery voltage (gray and black/white wires at the pump) thru the fusible link and the orange wire to the relay. The relay is controlled by the ECM thru the positive relay coil signal on the green/white wire.You might want to check the ground connection of the relay coil on the black/white wire. If that's good, maybe the ground wire to the pump is bad.
8/5/2011 12:34:29 AM •
1994 GMC Yukon
•
Answered
on Aug 05, 2011
•
275 views
Where is the oxygen sensor
Majority of GM that year is on the exhaust manifold or pipe coming off the manifold before it goes into the catalytic converter. Kind of looks like a spark plug with a wire coming off of it screwed into the pipe.
6/13/2011 6:20:00 PM •
1994 GMC Yukon
•
Answered
on Jun 13, 2011
•
314 views
Dies when slowing to a
The computer should be giving you a code without the code I would be guesing because I have seen this problem before. The usual cause of this problem is the Cam Sensor. Hook up a OBII code reader or get the computer scanned and I am almost positive it will be the Cam Sensor.
5/1/2011 5:55:41 PM •
1994 GMC Yukon
•
Answered
on May 01, 2011
•
50 views
When I first start my
I would suggest taking the oil pressure sender out and temporarily connecting a manual gauge to the engine. Run the engine until it's warm. If the manual gauge reads the same pressure as the electric one you may have a serious engine problem. If the manual gauge reads normal when the engine is warm the problem is probably with the gauge, most likely the sender.
4/10/2011 7:05:07 PM •
1994 GMC Yukon
•
Answered
on Apr 10, 2011
•
165 views
Dash lights don't work.
Hi, the bezel pulls straight off the dash. Then it's easy to see the back of the switch. Check the connector to see if maybe the fit is loose. Sometimes you can get a better connection by bending the blades slightly one left, the next right, etc. You only need to do it to the blades that run the dimmer wheel. It becomes trickier putting the connector back on, so don't bend them too far or push too hard when reconnecting. If that doesn't work, check the connection to the dimmer wheel. Try the same technique there. Let me know if you have any questions, and thanks for using FixYa.
Dimmer wheel
3/8/2011 12:32:46 AM •
1994 GMC Yukon
•
Answered
on Mar 08, 2011
•
200 views
Is it possible to adjust the tension of my fan
depending on the engine thats in you vehicle, all newer gm engines run an automatic tensioner. . the tensioners bind up with age and the belt will start to slip and make noise. if you change tyhe tensioner, change the belt at the same time... it doesnt take long for a slipping belt to get a "glaze" on it, and then your truck with its new tensioner might still squeak.
3/6/2011 3:38:46 PM •
1994 GMC Yukon
•
Answered
on Mar 06, 2011
•
147 views
Thought it might be the hubs due to 22 inch rims.
I'd be looking at driveshafts. They cause vibrations, rattles, squeaks and uncountable other symptoms. You didn't really say what was happening in your description. I'd be looking at driveline - driveshafts, hangar bearings and possibly transfer case and front bearings.
3/4/2011 8:32:48 AM •
1994 GMC Yukon
•
Answered
on Mar 04, 2011
•
143 views
Not finding what you are looking for?