20 Most Recent 2002 Ford F250 Super Duty SuperCab Questions & Answers

To achieve the recommended torque follow these steps:
1. Lubricate the bolt threads with engine oil
2. Torque them to 30 ft-lb
3. Using a torque angle gauge - add another 90-degree to it
4. Loosen head bolts by one turn
5. Again, torque them to 30 ft-lb
6. Add another 90-degrees
7. Finally, add another 90-degrees using a torque angle gauge.

2002 Ford F250... | Answered on May 19, 2020

Dirt or mud may entered the hub. Disassemble the unit clean and lubricate the system.

2002 Ford F250... | Answered on Oct 03, 2018

For Ford's fuse diagrams and schemes you may want to check Ford diagrams schemes imgVEHICLE com

2002 Ford F250... | Answered on Sep 26, 2018

There's a module under the truck by the transfer case check all fuses what year? and what size motor? Clean and use carbon conductive grease on plugs could be from corrosion and oxidation of the contacts post back with more info and write down everything that you did and I'll get you to the problem cause I'm a taxi mechanic in NYC and I have 50 years experience in all cars and trucks remember I'm not there so your post should be well thought out with the info before sending ok thanks Stephen

2002 Ford F250... | Answered on Feb 09, 2018

Your flexplate and/or torque convertor are out of balance.
If recently replaced it should be a warranty issue.
By your testing you have determined it's transmission related.
I have seen new/rebuilt torque convertors be balanced incorrectly.

2002 Ford F250... | Answered on Feb 07, 2018

I would start by unplugging the batteries for a few minutes and letting the system reset. Plug them back in and start her up. I had a similar issue and after driving a few blocks the light went off.

2002 Ford F250... | Answered on Jan 06, 2018

There is a relay. But first check for good ground on the black wire at the compressor clutch. Wiggle while testing to make sure it's good. If so, then suspect a bad relay. Relay is controlled by the PCM

2002 Ford F250... | Answered on Dec 26, 2017

shocks will be that same bolts and rubbers as OEM equipment
they are just more robust and engineered differently internally
talk wit suspension professional shops to get the right units for your application

2002 Ford F250... | Answered on Dec 16, 2017

Without testing the electronic's , hooking up a professional type scan tool an checking for DTC'S - diagnostic trouble code's etc ... we'd only be guessing . Probably the instrument cluster,but that is just a guess . Are you aware that the instrument cluster has a microprocessor an logic . Serial data communication network the modules share info. on ? Your vehicle has 10 or more modules (computers ) . What's the voltage at the battery terminals with the vehicle running ? Viewing wiring diagrams for electrical distribution an testing with a DMM - digital multi-meter would be a next step in the diagnostic procedure ,if no code's !
Electric Testing Techniques You Need to Know

Free wiring diagrams here http://www.bbbind.com/free_tsb.html Enter vehicle info. year , make , model an engine size . Under system click on body & accessories ,then under subsystem click on instrumentation . Click the search button then the blue link. Pull the instrument cluster ,with it still connected to the vehicle , check power an ground circuit's .

2002 Ford F250... | Answered on Dec 01, 2017

The park pawl inside the transmission is broken. It's a sizeable chunk of metal and needs to be replaced.

2002 Ford F250... | Answered on Nov 16, 2017

indicates a problem ground point or a problem BCM board

2002 Ford F250... | Answered on Nov 03, 2017

possible front drive shaft
they wear in the slip joint and any looseness in the "U" joints will cause a harmonic vibration that comes and goes

2002 Ford F250... | Answered on Oct 02, 2017

Pressure washing the engine certainly didn't do it any good. This is not recommended maintenance.

2002 Ford F250... | Answered on Aug 11, 2017

I would start with a service on it.

2002 Ford F250... | Answered on Aug 10, 2017

Try spraying some WD40 over the small switch that is half way down the front of both doors they are probably rusted up what we don't see much is what we all forget. should solve your problem. Hope this helps Best wishes, Malcolm Campbell.

2002 Ford F250... | Answered on Jul 03, 2017

Not finding what you are looking for?
2002 Ford F250 Super Duty SuperCab Logo

1,473 questions posted

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

F-250 Ford

  • F-250 Ford

Most Popular Question

fuse box diagram

  • Cars & Trucks