20 Most Recent 2001 Ford Mustang Questions & Answers

Open the fuel rail supply line at the fuel rail (need special tool) and pump the fuel out of the system until it no longer smells like diesel.

2001 Ford... | Answered on Jul 20, 2018

2001 ford mustang
I think you should try this website link that I have attached. It helps you repair your vehicle easily without more help. Ask the girl in chat at the bottom of the page

2001 Ford... | Answered on Feb 09, 2018

It covers all under repair manual. I have visited this website 2-3 times for the repair of Mustang manuals. They provide all kinds of manuals at a very cheap rates. Check it may be you will get something useful

2001 Ford... | Answered on Feb 02, 2018

Does occur in certain conditions? Like when the Air Conditioning is on? Check the a/c compressor if so.

2001 Ford... | Answered on Jan 29, 2018

The fuse doesn't blow till you turn on the light switch? If it blows before turning on light switch, look for a short to ground between fuse box and light switch.
If it blows after turning on light switch, I believe they make a short finder tool.

2001 Ford... | Answered on Jan 15, 2018

You did it like this ?
Programming -Keyless Entry Remote Transmitter NOTE: All keyless entry remote transmitters (15K601) must be programmed at the same time.
NOTE: All previous transmitter identification codes (TIC's) will be erased when programming mode is entered.
NOTE: To program (or reprogram) the keyless entry remote transmitters into the generic electronic module (GEM)(14B204), perform the following steps.
  1. Turn the ignition from OFF to RUN eight times within 10 seconds, ending in RUN. If the GEM has successfully entered program mode, it will lock and unlock all the doors.
  1. NOTE: The first TIC must be entered within 7.5 seconds of entering the program mode and additional TICs must be entered within 7.5 seconds of the first TIC. The programming mode is exited whenever the timing constraints are not met. Press any button on a keyless entry remote transmitter, and the doors will lock and then unlock to confirm that each keyless entry remote transmitter has been programmed.
  1. If the door locks do not respond for any keyless entry remote transmitter, wait for several seconds and press the button again.
  1. Turn the ignition switch to the OFF position, or wait up to five minutes after step 1, to exit program mode. If a keyless entry remote transmitter has been programmed (or reprogrammed), the GEM will lock and unlock all the doors one last time.

2001 Ford... | Answered on Jan 15, 2018

Fuel or spark issues can cause this . Transmission lockup clutch can make a chugging sensation . When in overdrive lightly touch the brake while keeping a steady throttle and see if the chugging stops . Post back .

2001 Ford... | Answered on Nov 25, 2017

Look in your owners manual under fuses from back of manual.

2001 Ford... | Answered on Nov 23, 2017

Check to make sure you have power to starter with multimeter at starter. If there is, replace starter. If not, trace ignition circuit back from starter.

2001 Ford... | Answered on Nov 23, 2017

disconnect the egy tube ftom the intake manifold/throttle body. clean the upening on yhrottle body and yube with either carburator or brake cleaner and a wire brush. Pretty simple, really nothing to it.

2001 Ford... | Answered on Nov 20, 2017

It can not crank and not turn over at the same time if it does not crank it wont turn over so which is it?

2001 Ford... | Answered on Nov 02, 2017

Try swapping out the power pcm relay. If the relay is good, replace the crankshaft position sensor.

2001 Ford... | Answered on Sep 09, 2017

There is a diagnostic procedure in the factory service repair manual for engine light lit ,no codes . Did you take it to ford dealer ? MIL - is referring to check engine , service engine soon etc...
  • MIL always on when engine is running (no DTCs):
  • MIL circuits
  • For Focus, Mustang, Town Car, Continental, LS6/LS8, Escape, Windstar, F-150, Expedition and Navigator/Blackwood:
  • Instrument Cluster, Section 413-01 of the Workshop Manual.
  • All Others:
  • GO to NB1

SERVICE ENGINE SOON indicator After the engine is started, the SERVICE ENGINE SOON indicator will prove out for a duration of three seconds. If the instrument cluster does not receive a message from the PCM within five seconds, the instrument cluster will illuminate the SERVICE ENGINE SOON indicator and log a diagnostic trouble code (DTC).

  • An indicator is inoperative/always on - SERVICE ENGINE SOON
  • Circuitry.
  • Bulb.
  • Instrument cluster.
  • PCM.
  • GO to Pinpoint Test P .

  • Did the SERVICE ENGINE SOON indicator illuminate?
Yes REFER to Powertrain Control/Emissions Diagnosis (PC/ED) manual.

No INSTALL a new instrument cluster; REFER to Instrument Cluster . CLEAR the DTCs. REPEAT the self-test.

2001 Ford... | Answered on Jul 18, 2017

The window motor must also be able to "go both ways".. check it..

2001 Ford... | Answered on Jun 14, 2017

Not finding what you are looking for?
2001 Ford Mustang Logo

967 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1998 Ford Mustang
1998 Ford Mustang

705 Questions

2000 Ford Mustang
2000 Ford Mustang

695 Questions

1995 Ford Mustang
1995 Ford Mustang

588 Questions

2002 Ford Mustang
2002 Ford Mustang

616 Questions

1996 Ford Mustang
1996 Ford Mustang

432 Questions

Top Ford Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Mustang Ford

  • Mustang Ford

Most Popular Question

coil 5 located 2001 mustang gt

  • Cars & Trucks