20 Most Recent 2000 Ford Mustang Questions & Answers

The part itself depending on where you buy it is between $6.00 -$15.00 the labor depends on the shop you can do this very easily with a little bit of tools jack up the rear of the car mark the drive shaft remove the bolts that attach it to the rear end then move the drive shaft back to get it out of the tail of the transmission then pry out the seal be careful that you don't Crack the tail case light tapping with a hammer will work to pry out the old seal then apply grease to the new one inside and out and lightly tap it in flush with the tail housing reinstall the drive shaft with the marks lined up and tighten the fasteners and guess what you did it and your done there is a flat space in the spline of the drive shaft that mates with the output shaft of the transmission in case you have problems lining up the drive shaft ok this is very simple to do

2000 Ford... | Answered on Jun 30, 2019

There's a switch in the lock itself in the trunk if you have a continuity tester check the release button first then the wires going to the trunk make long jumper wires from speaker wire and check for continuity then try jumping the lock itself with battery power and see if it works there is an accessory relay for that stuff but is everything else working door locks windows etc. ? That's in your passenger fuse box if all is working that's not it and go with the continuity checks pull out the glove box switch and touch the switch pins with each lead then press the button if the tester light comes on or meter beeps the switch is fine go to the wires next and do the same thing one end at the glove box plug to the other in the trunk for each wire if they light up or beep all good and the lock maybe bad if no beeps or lighting there's a wire break and check by sections at a time good luck stephen

2000 Ford... | Answered on May 24, 2019

how to set up seat belt disable to start engine without driving not seat belt

2000 Ford... | Answered on Mar 18, 2019

This website www.reliable-store.com has the
largest collection of repair, service, parts manuals of any vehicle on earth. Best website I came across for manuals.. Also have live assistance

2000 Ford... | Answered on Mar 08, 2018

Make? Model?

2000 Ford... | Answered on Jan 07, 2018

it is possible the light switch is faulty

2000 Ford... | Answered on Jan 06, 2018

camshaft bearing maybe

2000 Ford... | Answered on Dec 22, 2017

-Sounds like blow head gasket, broken or burn valve.
-Do compression check each cylinder to see what you have and compare to its specification.
-Was it recently rebuild?
If so then timing might be off.
spark plug wire connect to the wrong spark plug.
Vacuum line might connect to the wrong line.
Bad rotor or cap .

Good luck


2000 Ford... | Answered on Nov 27, 2017

Disconnect battery for at least 2 hours.
Hold negative and positive leads together for 5 minutes.
PUT KEY IN THE IGNITION, but not turned on.
Connect POSITIVE lead.
Connect negative lead in one swift movement.
Wait 15 minutes for chip in ignition switch and chip in the key to be recognised by the ECM.
Start the vehicle.

2000 Ford... | Answered on Nov 22, 2017

use a scan tool to reset the ECM to get the immobilizer to work

2000 Ford... | Answered on Nov 15, 2017

get under the vehicle (use ramps) and check all linkages for movement pull push on the anti roll bar links, pull push on steering rack and pinion and linkages, any excessive movement, jack each wheel at a time, using a bar check the lower wishbone joints for movement, get the bar in the gap between the wishbone and lower part of the shock. and pull down, if any movement in ball joint up and down replace. while wheel on vehicle check for movement in bearing you will feel a tiny amount not much but pull and push on wheel with opposite hands on 12 o'clock and 6 o'clock and do the same at 9 and 3. now with both wheels off the ground but with the tyres still on, have some one holed one wheel and push pull on wheels each side there should be even movement between both wheels, if everything is fine with the the steering linkages and this dose not feel or sound right then this could be the problem also to add if the inside and out side of the tyres are wearing then the tyre pressure is wrong and needs adjusting to the right tyre pressure .

2000 Ford... | Answered on Jul 24, 2017

On your fuse panel, check the fuse that says ign.it is the 4th one back from the front and is a 40 amp fuse.

2000 Ford... | Answered on Jul 22, 2017

Does the mustang have independent (IRS) axel or the solid 8.8 rear axel?

2000 Ford... | Answered on Jun 12, 2017

Not finding what you are looking for?
2000 Ford Mustang Logo

1,008 questions posted

Ask a Question

Usually answered in minutes!

Popular Products

1998 Ford Mustang
1998 Ford Mustang

679 Questions

2001 Ford Mustang
2001 Ford Mustang

632 Questions

2002 Ford Mustang
2002 Ford Mustang

587 Questions

1995 Ford Mustang
1995 Ford Mustang

574 Questions

1996 Ford Mustang
1996 Ford Mustang

418 Questions

Top Ford Experts


Level 3 Expert

85239 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22485 Answers

gerry bissi

Level 3 Expert

4388 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

View Most Popular

Mustang Ford

  • Mustang Ford

Most Popular Question

motor shakes very bad

  • Cars & Trucks